研究発表 - 荒木 拓人
件数 80 件-
OBSERVATION OF CONDENSATE DROPS FREEZING ON MICRO STRUCTURED METAL SURFACES PROCESSED BY WET ETCHING
Kota Asaoka, Shoki Inoue, Tatsuya Mizusawa and Takuto Araki
The 32nd International Symposium on Transport Phenomena
開催年月日: 2022年3月
記述言語:英語 会議種別:口頭発表(一般)
-
THREE-DIMENSIONAL ELECTRIC POTENTIAL SIMULATION WITH VARIOUS ELECTRODE GEOMETRIES IN PEM WATER ELECTROLYSIS
Naruhisa Tsukase, Konosuke Watanabe, Takuto Araki, Taiki Ishida, Kensaku Nagasawa, Yoshiyuki Kuroda and Shigenori Mitsushima
The 32nd International Symposium on Transport Phenomena
開催年月日: 2022年3月
記述言語:英語 会議種別:口頭発表(一般)
-
In Situ X-Ray Diffraction Study of Iridium Crystalline Structure Under Working Conditions of Proton Exchange Membrane Water Electrolysis
K Shigemasa, M Shviro, Y Kuroda, S Mitsushima, M Carmo, T Araki
ECS Meeting
開催年月日: 2021年10月
記述言語:英語 会議種別:口頭発表(一般)
-
Observation of Oxygen Bubble Growth near Anode Catalyst Electrode in PEM Water Electrolyzer
Konosuke Watanabe, Kohei Wakuda, Kodai Wani, Takuto Araki, Kensaku Nagasawa, Shigenori Mitsushima
ECS Meeting
開催年月日: 2021年10月
記述言語:英語 会議種別:口頭発表(一般)
-
MEMS sensor development for making PEFC catalyst layer during drying process
Yoshifumi Hyugaji, Takuto Araki (Yokohama National University, Faculty of Engineering), Keisuke Nagato, Kohei Nagai, Takuya Tsujiguchi, Kota Asaoka, Daichi Suzuki
The 2nd Asian Conference on Thermal Sciences 2021年10月
開催年月日: 2021年10月
記述言語:英語 会議種別:口頭発表(一般)
-
荒木拓人 [招待有り]
第150回燃料電池研究会セミナー 電気化学会
開催年月日: 2021年4月
記述言語:日本語 会議種別:口頭発表(招待・特別)
-
物理蒸着法による極薄熱電対の作製と燃料電池内の温度測定
荒木拓人
第73回CVD研究会
開催年月日: 2021年3月
記述言語:日本語 会議種別:口頭発表(招待・特別)
-
固体酸化物共電解・メタネーションを用いたPtGシステムの効率解析
太田篤人,河村駿希,李坤朋,矢野佑磨,荒木拓人,森昌史,
第28回SOFC研究発表会 SOFC研究会
開催年月日: 2020年12月
記述言語:日本語 会議種別:口頭発表(一般)
-
Separation of Polarizations Using Shifted Electrode Arrangement in Proton Exchange Membrane Water Electrolysis
K. Watanabe, T. Araki, K. Nagasawa, Y. Kuroda, and S. Mitsushima
ECS PRIME ECS
開催年月日: 2020年10月
記述言語:英語 会議種別:口頭発表(一般)
-
Double Point Temperature Measurements Under Rib and Channel in an Operating PEFC Using MEMS Sensors
K. Shigemasa, Y. Otsuki, M. Kurosu, H. Sato, and T. Araki
ECS PRIME ECS
開催年月日: 2020年10月
記述言語:英語 会議種別:口頭発表(一般)
-
Visualization of Bubble Behavior on Hydrophobic Coated CL in PEM Water Electrolysis Cell
K. Wani, T. Araki, K. Nagasawa, and S. Mitsushima
ECS PRIME ECS
開催年月日: 2020年10月
記述言語:英語 会議種別:口頭発表(一般)
-
Nernst-Planckモデルを用いたプロトン伝導性セラミック燃料電池(PCFC)電解質における電流効率のガス濃度分布依存性に関する数値解析
李 坤朋, 河村 駿希, 太田 篤人, 荒木 拓人, 奥山 勇冶
第57回日本伝熱シンポジウム 日本伝熱学会
開催年月日: 2020年6月
記述言語:日本語 会議種別:口頭発表(一般)
-
PEM水電解における参照極を用いた過電圧分離に関する数値解析
渡邊 孝之介, 井上 翔輝, 柏木 勇人, 長澤 兼作, 黒田 義之, 光島 重徳, 荒木 拓人
第57回日本伝熱シンポジウム 日本伝熱学会
開催年月日: 2020年6月
記述言語:日本語 会議種別:口頭発表(一般)
-
MPL濡れ性分布配置がGDL液水分布に与える影響
佐藤 颯, 荒木 拓人, 王 世学, 王 国卓, 宇高 義郎
第57回日本伝熱シンポジウム 日本伝熱学会
開催年月日: 2020年6月
記述言語:日本語 会議種別:口頭発表(一般)
-
固体高分子形水電解で発生する酸素気泡の可視光カメラによる挙動観察
中山 武志, 渡邊 孝之介, 荒木 拓人
動力・エネルギー技術の最前線講演論文集 : シンポジウム 2019年 一般社団法人 日本機械学会
開催年月日: 2019年
記述言語:日本語 会議種別:その他
In order to construct a hydrogen energy system, water electrolysis technology for converting renewable energy into hydrogen has recently attracted attention. In particular, a proton exchange membrane (PEM) water electrolysis can be operated at high current density and can produce high purity hydrogen compared to other water electrolysis techniques. However, increasing th0e efficiency is indispensable for putting PEM water electrolysis into practical use in the future. One of the serious problems is that the staying of generated oxygen bubbles in the reaction site inhibits the water supply and significantly reduces the reaction efficiency. However, the mechanism of generation, growth and detachment of oxygen bubbles on the reaction site in the PEM electrolyzer has not been clarified. Therefore, in this research, in order to understand the two-phase flow phenomenon of this oxygen bubble, the behavior of the bubbles was observed using a visible light high-speed camera and a visualized electrolysis cell.
-
神﨑 崇志, 丸尾 昭二, 渡邉 正義, 上野 和英, 太田 裕貴, 斎藤 聖, 小槻 耀太, 松田 涼佑, 磯田 豊, 遠藤 拓馬, 中村 史香, 荒木 拓人, 古川 太一
マイクロ・ナノ工学シンポジウム 2019年 一般社団法人 日本機械学会
開催年月日: 2019年
記述言語:日本語 会議種別:その他
<p>Liquid-state electronics utilizing functional liquids confined in soft templates as the sensing and actuating component present the ideal platform for enabling conformal coverage of electronic systems on curved and soft surfaces. However, to date, optoelectronic devices based on functional liquid materials as represented by photodetectors and optical memories still have not been proposed; this advancement is crucial to scaling up current liquid-state devices to a system level. Here, this study proposes optoelectronic devices based on liquid metal and photo-switchable ionic liquid with liquid-liquid heterojunction technology. The sensing and memory schemes we present are generic for different liquid-state devices, enabling different functionality to be added to the liquid-state electronics. As a proof of concept, we demonstrate a light sensor composed of the ionic liquid, and an optical memory using a composite of the ionic liquid and polypropylene glycol. These devices are important advancements towards the realization of liquid-state electronic systems.</p>
-
供給ガス中の酸素濃度が共電解SOECシステム効率へ与える影響
河村 駿希, 太田篤人, 荒木拓人, 森昌史
第28回日本MRS年次大会
開催年月日: 2018年12月
記述言語:日本語 会議種別:口頭発表(一般)
開催地:北九州国際会議場
-
Improved Sensitivity of Thin Film Sensor for Humidity Measurement inside a Operating PEMFC
N. Hasegawa, Y. Otsuki, M. Kurosu, and T. Araki
Power MEMS 2018
開催年月日: 2018年12月
記述言語:英語 会議種別:ポスター発表
開催地:Miami USA
-
Visualization and multi-physical analysis of two phase flow inside Electrochemical energy devices
Konosuke Watanabe, Takuto Araki
2nd International Workshop on Phase Interfaces for Highly Efficient Energy Utilization
開催年月日: 2018年11月
記述言語:英語 会議種別:ポスター発表
開催地:Baltimore Marriott InnerHarborat Comden Yard (MD, USA)
-
Multi-physical approach for fuel cells
Takuto ARAKI [招待有り]
2nd International Workshop on Phase Interfaces for Highly Efficient Energy Utilization
開催年月日: 2018年11月
記述言語:英語 会議種別:口頭発表(招待・特別)
開催地:Baltimore Marriott InnerHarborat Comden Yard (MD, USA)
-
Visualization and multi-physical analysis of two phase flow inside Electrochemical energy devices
Konosuke Watanabe, Takuto Araki
2nd International Workshop on Phase Interfaces for Highly Efficient Energy Utilization
開催年月日: 2018年11月
記述言語:英語 会議種別:口頭発表(一般)
開催地:Baltimore Marriott InnerHarborat Comden Yard(MD, USA)
-
Hybrid GDLによる撥水パターンのセル内配置が液水分布に与える影響
重政 海都, 佐藤 颯, 荒木 拓人
熱工学コンファレンス
開催年月日: 2018年10月
記述言語:日本語 会議種別:口頭発表(一般)
開催地:富山大学
-
固体高分子形燃料電池の低温運転において膜物性がセル性能に与える影響
西村 理志, 井上 翔輝, 高橋 俊太, 荒木 拓人
熱工学コンファレンス
開催年月日: 2018年10月
記述言語:日本語 会議種別:口頭発表(一般)
開催地:富山大学
-
Modeling of Temperature Distribution in a Proton-Conductive Ceramic Fuel Cell
Takuto Araki, Yuji Okuyama, Kunpeng Li, Kawamura Toshiki, Toshiaki Yamaguchi and Hiroyuki Shimada
234th ECS Meeting
開催年月日: 2018年10月
記述言語:英語 会議種別:口頭発表(一般)
開催地: Cancun, Mexico
-
Electrical Efficiency And Thermal Autonomy of Powergeneration System Using Protonic Ceramic Fuel Cell
Takeshi Nakayama1, Toshiki Kawamura2, , and Takuto Araki
4th International Workshop on Hydrogen and Fuel Cells
開催年月日: 2018年8月
記述言語:英語 会議種別:ポスター発表
開催地:TU Graz, Graz
-
Effects of the existence of MPL and GDL porosity to the local temperature and water distribution in the PEFC,
Kaito Shigemasa, Takuto Araki
the 15th Joint Symposium between Sister Universities in Mechanical Engineering
開催年月日: 2018年8月
記述言語:英語 会議種別:口頭発表(一般)
開催地:Hamamatsu, Japan
-
Numerical Analysis of Water Freezing at Cold Startup of Polymer Electrolyte Fuel Cells
Satoshi Nishimura, Shoki Inoue, Yusuke, Tamada, Yota Otsuki, Takuto Araki
the 15th Joint Symposium between Sister Universities in Mechanical Engineering
開催年月日: 2018年8月
記述言語:英語 会議種別:口頭発表(一般)
開催地:Hamamatsu, Japan
-
Hydrogen concentration distribution visualization of gdl during pefc start-up
K. Watanabe, K. Hamada, T. Araki
Grand Renewable Energy 2018,
開催年月日: 2018年7月
記述言語:英語 会議種別:口頭発表(一般)
開催地:Pacifico Yokohama
-
Numerical analysis of the distributions of current efficiency inside a PCSOFC
Kunpeng Li , Takuto Araki, Atushi Maeda, Kohei Shimosawa, Yuji Okuyama,
13th EUROPEAN SOFC & SOE FORUM 2018
開催年月日: 2018年7月
記述言語:英語 会議種別:ポスター発表
開催地:Lucerne, Switzerland
-
直接ギ酸形燃料電池における発生気泡のX線CT可視化
渡邊孝之介(横浜国大), 重政海都, 望月亮太(金沢大), 辻口拓也, 荒木拓人(横浜国大)
第23回動力・エネルギー技術シンポジウム
開催年月日: 2018年6月
記述言語:日本語 会議種別:口頭発表(一般)
開催地:国際ホテル宇部(山口県宇部市)
-
プロトン伝導型SOFCの運転条件がホール電流分布に与える影響
河村駿希, 荒木拓人, 下沢航平, 前田厚史, 李坤朋(横浜国立大), 奥山勇治(宮崎大学)
第55回伝熱シンポジウム
開催年月日: 2018年5月
記述言語:日本語 会議種別:口頭発表(一般)
開催地:札幌コンベンションセンター
-
PEFC氷点下起動時の過冷却水凍結に伴う凝固熱の測定
玉田裕介, 小槻耀太, 西村理志, 井上翔輝, 荒木拓人
第55回伝熱シンポジウム
開催年月日: 2018年5月
記述言語:日本語 会議種別:口頭発表(一般)
開催地:札幌コンベンションセンター
-
Hybrid GDLによる撥水パターンのセル内配置が液水分布に与える影響
重政 海都, 佐藤 颯, 荒木 拓人, 宇高 義郎, 王 世学
熱工学コンファレンス講演論文集 2018年 一般社団法人 日本機械学会
開催年月日: 2018年
記述言語:日本語 会議種別:その他
<p>A polymer Electrolyte Fuel Cell (PEFC) has higher power density than other fuel cells and has been partially put into practical use. However, there are many problems and one of most important tasks is the management of water distribution inside PEFC. To realize this management, we can use Hybrid GDL. There are hydrophobic and hydrophilic area alternately on Hybrid GDL. We know Hybrid GDL causes higher performance of PEFC, but we don’t know about the detail why Hybrid GDL do so. Therefore, we visualized inside PEFC with Hybrid GDL during operating by using X-ray CT machine. From these results, we investigated how configuration of Hybrid GDL inside PEFC affects water distribution.</p>
-
薄膜センサを用いた固体高分子形燃料電池内MEA膜厚方向の湿度測定
長谷川 実慶, 南 凌太朗, 黒須 雅人, 荒木 拓人
マイクロ・ナノ工学シンポジウム 2018年 一般社団法人 日本機械学会
開催年月日: 2018年
記述言語:日本語 会議種別:その他
<p>Measuring local humidity inside a polymer electrolyte fuel cell (PEFC) is essential for proper water management because water condition is closely related to the cell performance. Thin film humidity sensors (TFHSs) were fabricated by the MEMS techniques for measuring local humidity inside a membrane electrode assembly (MEA). The sensor was placed between a CL and a micro porous layer (MPL). Both of the anode and cathode side humidity measurements were conducted with two types of membrane thickness. There was no significant performance reduction owing to the insertion of the TFHS. Both types of the membrane, the humidity difference between the anode and the cathode CL surface in the high humidity supply gas condition was smaller than in the low humidity condition because of the higher water diffusion coefficient of the PEM. When thick membrane is used, severe drying on the anode side caused performance degradation due to the large water.</p>
-
渡邊 孝之介, 重政 海都, 望月 亮太, 辻口 拓也, 荒木 拓人
動力・エネルギー技術の最前線講演論文集 : シンポジウム 2018年 一般社団法人 日本機械学会
開催年月日: 2018年
記述言語:日本語 会議種別:その他
Recently, formic acid is expected as one of the energy career of renewable energy. Especially, A direct formic acid fuel cell, DFAFC, has received considerable attention since it can generate higher power density than the other direct liquid fuel cells and its power density is comparable to that of a polymer electrolyte fuel cell, PEFC, operated with hydrogen and oxygen at room temperature. However, CO<sub>2</sub> gas is generated in the anode reaction when a DFAFC is operating. If CO<sub>2</sub> bubbles stay in the anode gas diffusion layer, GDL, the mass transport resistance in a GDL increases and the generated power of a DFAFC decreases with the lapse of time. Furthermore, the gas-liquid two-phase flow behavior in a GDL, which is porous material, is not clear. In this study, we investigated the effect of Anode GDL configuration on power generation characteristics and bubbles behavior by visualizing CO<sub>2</sub> bubbles distribution using Xray CT.
-
固体高分子形燃料電池の低温運転において膜物性がセル性能に与える影響
西村 理志, 井上 翔輝, 高橋 俊太, 荒木 拓人
熱工学コンファレンス講演論文集 2018年 一般社団法人 日本機械学会
開催年月日: 2018年
記述言語:日本語 会議種別:その他
<p>Polymer electrolyte fuel cells (PEFCs) have less environmental impact and higher efficiency, so that they have been applied for vehicles. PEFCs are usually operated at about 70°C, but it is necessary to operate them stably at lower temperatures for wide application. The properties of a polymer electrolyte membrane might be dependent on temperature and have effect on cell performance. In this study, we used a two-dimensional model incorporating electrochemical kinetics and transport phenomena of mass, charge and heat to investigate the effect of membrane properties on cell performance at lower temperatures.</p>
-
トポロジー最適化を用いた水冷ヒートシンクの作製トポロジー最適化を用いた水冷ヒートシンクの作製
松田 涼佑, 神崎 崇, 野口 悠暉, 佐藤 綾美, 佐藤 勇気, 古川 太一, 荒木 拓人, 丸尾 昭二, 山田 崇恭, 西脇 眞二, 太田 裕貴
マイクロ・ナノ工学シンポジウム 2018年 一般社団法人 日本機械学会
開催年月日: 2018年
記述言語:日本語 会議種別:その他
<p>In this study, water heat sink using topology-optimized microchannels was developed for higher efficient cooling of circuits(Fig.1). The temperature of a resistive heater under a heat sink using topology-optimized microchannels was 4°C lower than that under common-channels. This result indicates that topology optimization is suitable for the design of an efficient heat sink. Heat sinks composed of microchannels have been developed in order to satisfy high demand for the increase of heat value generated from circuits[1]. However, this design of microchannels is still not optimized for efficient cooling. In this study, advanced mathematical method called topology optimization was utilized to gain higher efficiency for cooling. As a result, fabricated sink demonstrated more efficient cooling effect to a resistive heater imitating electrical components. This result suggests possibility to manage heat generated from high-density electric devices more appropriately.</p>
-
Power to Gas 技術について -共電解を利用したSOEC型メタン混合ガス製造システムおよび製造ガスの都市ガスパイプラインへの供給検討
荒木 拓人
第1回 低炭素技術研究会
開催年月日: 2017年12月
記述言語:英語 会議種別:口頭発表(一般)
開催地:一般社団法人日本ガス協会ビル 7階 701会議室
-
GDL構成がPEFC内の温度勾配および液水輸送に与える影響
橋村蒼太, 玉田裕介, 小林航輝, 南凌太郎, 長谷川実慶, 宮川聖史, 高谷洸司, 荒木拓人
第54回日本伝熱シンポジウム
開催年月日: 2017年5月
記述言語:日本語 会議種別:口頭発表(一般)
開催地:大宮ソニックシティ
-
多孔質における非定常水素濃度分布の可視化手法の開発
濱田高志, 渡邊孝之介(横国大), RAHMAN Khalilur (スズキ), 荒木拓人(横国大)
第54回日本伝熱シンポジウム
開催年月日: 2017年5月
記述言語:日本語 会議種別:口頭発表(一般)
開催地:大宮ソニックシティ
-
Development of micro sensors for in-situ local humidity measurements inside a PEMFC
Ryotaro Mianmi, Takuto Araki
The 6th International Symposium on Micro and Nano Technology
開催年月日: 2017年3月
記述言語:英語 会議種別:口頭発表(一般)
開催地:Kyushu University
-
薄膜センサーを用いた固体高分子形燃料電池カソード流路内湿度分布の非定常測定
長谷川 実慶, 南 凌太郎, 荒木 拓人
マイクロ・ナノ工学シンポジウム 2017年 一般社団法人 日本機械学会
開催年月日: 2017年
記述言語:日本語 会議種別:その他
The polymer electrolyte fuel cell (PEFC) is a clean and high efficiency power generation system. However, there are still several issues to be solved commonly used. One of the most serious issues accumulated in a channel, a catalyst layer, a gas diffusion layer lead to PEFC performance degradation because too much liquid water disturbs the reactant gas to the reaction site. In addition, the inside of PEFC is complex system because of two-phase flow of liquid water and vapor. So, we need to focus on the vapor transport as well as liquid water to reveal water transport inside the cell. There are some approaches to comprehend the RH inside PEFCs. However, the methods of these reports could not measure unsteady humidity at a channel. So, we have developed thin film humidity sensor (TFHS) using micro-electro-mechanical-systems (MEMS) technology for unsteady measurements of humidity distribution in a cathode channel.
-
小型円筒水蒸気電解セルにおける非定常温度分布
前田厚史, 渡邉憲太郎, 荒木拓人, 森昌史
第25回SOFC研究発表会
開催年月日: 2016年6月
記述言語:日本語 会議種別:口頭発表(一般)
開催地:科学技術館
-
島田 寛之, 山口 十志明, 荒木 拓人, 水澤 竜也, 森 昌史, 藤代 芳伸
電気化学および工業物理化学 2016年 公益社団法人 電気化学会
開催年月日: 2016年
記述言語:英語 会議種別:その他
-
荒木 拓人, 水澤 竜也
電気化学および工業物理化学 2016年 公益社団法人 電気化学会
開催年月日: 2016年
記述言語:英語 会議種別:その他
-
渡邉 憲太郎, 前田 厚史, 水澤 竜也, 荒木 拓人, 森 昌史
動力・エネルギー技術の最前線講演論文集 : シンポジウム 2016年 一般社団法人 日本機械学会
開催年月日: 2016年
記述言語:日本語 会議種別:その他
<p>Hydrogen production techonology by the H<sub>2</sub>O electrolysis using renewable energy attracts attention. However, there still remains many problems such as a storage and transportation Unlike hydrogen, the storage of alkane with a high energy density is already established and spread. Solid Oxide Electrolysis Cells (SOECs) can convert carbon dioxide and steam to CO and H<sub>2</sub>. This mixture gas is an important feedstock for alkane synthesis through Fischer-Tropsch (F-T) process. In this study, the propane production system is proposed with the SOEC co-electrolysis and FT process. The energy efficiency and molar ratio of the outlet gas are calculated by a cycle analysis.</p>
-
濱田 高志, 篠田 魁人, 荒木 拓人
動力・エネルギー技術の最前線講演論文集 : シンポジウム 2016年 一般社団法人 日本機械学会
開催年月日: 2016年
記述言語:日本語 会議種別:その他
<p>Microbial fuel cells (MFC) produce electricity using electron and hydrogen which are emitted from microorganisms. This technology has been promised to be used mainly in sewage treatment facilities. But when it comes to practical using, MFC has low power densities so that it is difficult to use as the power source. We modified the cathode structure to improve MFC's performance. In this study, we tested four kinds of PEM (Nafion®), which are different thickness. Also we supplied oxygen to cathode GDL to examine the relation with oxygen flow rate and PEM. The results showed relatively low flow rates had better better performance than high flow rates. Excess oxygen supply might cause drying of the surface of the membrane, which might prevent proton conduction. This tendency was confirmed in all membranes. Although excess oxygen supply was not good for MFC, it showed better performance than air breathing MFC.</p>
-
マルチスケール数値解析による熱・物質輸送-電気化学反応の連成現象解明とセンサ開発
荒木 拓人
年次大会 2016年 一般社団法人 日本機械学会
開催年月日: 2016年
記述言語:日本語 会議種別:その他
-
29pm1-E-2 固体高分子形燃料電池内の湿度測定に向けたMEMSセンサの小型化
辻川 順, 小林 航輝, 南 凌太郎, 荒木 拓人
マイクロ・ナノ工学シンポジウム 2015年 一般社団法人 日本機械学会
開催年月日: 2015年
記述言語:日本語 会議種別:その他
Proton exchange membrane fuel cells (PEMFCs) are promising systems for mobile and vehicle applications because of their high power density and low operating temperature. This characteristic causes the several problems, such as water management. Then for measuring the local humidity inside membrane electrode assembly (MEA), the thin film humidity sensors are fabricated by the micro-electro-mechanical systems (MEMS) based techniques. The sensor was placed between the catalyst layer (CL) and the microporous layer (MPL) at the cathode. The slight effects on total cell performance were observed with the insertion of it. In-situ measurement with a humidity sensor showed the capacitance and RH increased with the increase of the current density linearly up to 0.3 A/cm^2. The capacitance change became moderate in the region of current density 0.3 A/cm^2, because the relative humidity reached 100% at the 0.3 A/cm^2 and water started to accumulate.
-
D222 薄膜熱電対を用いたPEFC内局所温度の多点同時測定(OS-05:燃料電池・二次電池関連研究の新展開(3))
小林 航輝, 辻川 順, 荒木 拓人
熱工学コンファレンス講演論文集 2015年 一般社団法人 日本機械学会
開催年月日: 2015年
記述言語:日本語 会議種別:その他
The water management has a significant effect on power generation performance of the Polymer electrolyte fuel cell (PEFC). Water distribution and temperature distribution give interaction, then the temperature distribution is required for optimizing the water management. Thus to obtain the temperature distribution by the multipoint measurements are important. We have developed the thin film thermocouples by using Micro Electronic Mechanical Systems (MEMS) technology, and the thermocouples are inserted and measured multipoint of local temperature in cells. Finally, we measured temperature difference of 2 degrees between the current collector and the CL.
-
21am2-A6 固体高分子形燃料電池触媒層表面の温度・湿度測定に向けたセンサ開発
キム スンヨン, 杉本 俊樹, 荒木 拓人
マイクロ・ナノ工学シンポジウム 2014年 一般社団法人 日本機械学会
開催年月日: 2014年
記述言語:日本語 会議種別:その他
Proton exchange membrane fuel cells (PEMFCs) are useful systems because they operate at lower temperatures than other types of fuel cells. This characteristic causes water management issues. To elucidate effects of water on PEMFC performance, we developed a temperature sensor using micro-electro-mechanical systems (MEMS) techniques. This sensor was placed between the catalyst layer (CL) and the microporous layer (MPL) at the cathode. Slight effects on total cell performance were observed with the insertion of the sensor. This sensor can be applicable to typical PEMFCs without any special equipment such as a transparent separator. In-situ measurement with a temperature sensor showed that the maximum temperature rise at the cathode CL (CCL) was about 9 ℃ at 1.1 A/cm^2. The temperature sensor also showed temperature gradients between the ribs and channels. In addition, we developed a capacitance-type humidity sensor and inserted it in the channel. In-situ measurement with a humidity sensor showed a relative humidity (RH) change in the channel.
-
内部水蒸気改質法を用いた家庭用SOFC給湯給電システムに関する定常サイクル計算
水澤 竜也, 武藤 崇史, 荒木 拓人, 岡田 文男, 廣山 徹, 水谷 安伸
日本機械学会論文集 2014年 一般社団法人 日本機械学会
開催年月日: 2014年
記述言語:日本語 会議種別:その他
In this paper, partial load efficiencies of three types of SOFC combined heat and power systems were calculated by cycle analysis. SOFC means Solid Oxide Fuel Cells. The systems were external fuel reforming system (ER type), internal fuel reforming system (IRa type) and internal fuel reforming system with different configuration (IRb type). In each system, the operating temperature of SOFC was 650<sup><i>◦</i></sup>C. The rated point of electrical power generation of SOFC stack was 560W. Fuel was assumed city gas 13A. At the rated points, results of electrical efficiency by cycle analysis were 39.1%, 41.4% and 41.4% at ER type system, IRa type system, IRb type system, respectively. Electrical efficiency of internal reforming system is higher than that of external system. However, the part load area of IRa type system was narrower than that of ER type system because heat recyle was difficult for IRa type system. The part load area of IRb type system was wider than that of IRa type system due to difference of configuration.
-
A112 SOEC水蒸気電解システムのサイクル計算とエクセルギー解析(OS5 水素・燃料電池(2))
武藤 崇史, 水澤 竜也, 荒木 拓人, 森 昌史
動力・エネルギー技術の最前線講演論文集 : シンポジウム 2013年 一般社団法人 日本機械学会
開催年月日: 2013年
記述言語:日本語 会議種別:その他
Cells with solid oxide electrolyte can be applied for a hydrogen generator, namely Solid Oxide Electrolysis Cells SOECs (SOECs) In this study, we carried out the cycle analysis foi SOEC systems following two steps Firstly, SOEC system models with H2 production capacity of 300 Nm3/h were constructed Secondly, system efficiency was calculated based on heat and mass balance from a viewpoint of "exergy" We treated two cases of SOEC systems which have different operating temperatures, 850°C and 650℃ As a result, several factors which decide property of exergy efficiency were obtained. At load rate with endothermic reaction, the balance of temperature of heat source and stack performance is primary factor for exergy efficiency On the other side, the heat loss is more important factor at load rate with exothermic reaction Therefore it is important to select the suitable system considering the operating conditions such as load range of SOEC systems
-
I144 MEMSセンサーを用いた固体高分子形燃料電池内のin-situ湿度測定(OS-5:燃料電池・二次電池関連研究の新展開(4))
堀内 悠平, 杉本 俊樹, 荒木 拓人
熱工学コンファレンス講演論文集 2013年 一般社団法人 日本機械学会
開催年月日: 2013年
記述言語:日本語 会議種別:その他
In order to measure humidity inside PEFC, we developed flexible and thin film capacitive humidity sensor by micro-electro-mechanical-systems (MEMS) technology. The sensor consists of parylene and Ni. Parylene was selected as an electrical isolating material and also sensing material. Ni electrodes was deposited thinly to obtain water vapor permeability to the sensing material. Sensing area and thickness of the sensor are 4mm^2 and 6.51μm respectively. By the calibration measurement, the sensor has high sensitivity of 31.8%. It means that the sensor has a high reproducibility and small error. Furthermore, the sensor demonstrated a very small hysteresis in the range from 60%RH to 100%RH.
-
武藤 崇史, 水澤 竜也, 森 昌史, 荒木 拓人
日本機械学会論文集B編 2013年 一般社団法人 日本機械学会
開催年月日: 2013年
記述言語:日本語 会議種別:その他
Solid Oxide Electrolysis Cells (SOECs) can be used for hydrogen generator systems. In this study, two types of SOECs which have different operating temperatures, 850°C and 650°C, were treated. For 850°C-type cell, measurements of current density-voltage characteristic and current efficiency were carried out and the data of 650°C-type cell were obtained from the previous report. For 850°C-type cell, the voltage at 0.4 A/cm<sup>2</sup> was 1.20V and the current efficiency was approximately 100%. With the experimental values, cycle calculations for SOEC system models with production capacity of 300Nm<sup>3</sup>/h were carried out. At a rated operating point of 0.4A/cm<sup>2</sup>, the exergy efficiencies depending on each source of supplied energy were discussed. When all energy was supplied by electricity, the exergy efficiencies were 80.2% for 850°C-type system and 80.5% for 650°C-type one. When heat of 110°C was supplied, efficiencies were 89.2% for 850°C-type system and 90.5% for 650°C-type one. When heats of 110°C and 850°C or 650°C were supplied, they were 91.4% for both systems. The efficiencies were also discussed at various electric supply loads. At the load area< 950kW, 650°C-type system had higher efficiency than that of 850°C-type one. On the other hand, at the load area> 950kW, the efficiency of 850°C system was higher.
-
PEFC用GDL流路界面における物質伝達抵抗および内部有効拡散係数の異方性測定
金子 春樹, 太田 公一, 清水 雅也, 荒木 拓人
日本機械学会論文集B編 2013年 一般社団法人 日本機械学会
開催年月日: 2013年
記述言語:日本語 会議種別:その他
Gas transport through the gas diffusion layer (GDL) is important in Polymer Electrolyte Fuel Cell (PEFC). GDL consists of random fiber structure, so GDL may have anisotropy for the transport properties. We have developed the measuring method of the effective diffusivity through GDLs and measured those through-plane and in-plane values. In this work, the effective diffusivity through GDL on each directions and the convection mass transfer at GDL-Channel interface were investigated. The coefficient has been measured in various gas flow rate and diffusion area of GDL of especially through-plane direction. It was found that the in-plane diffusivity is higher than the through-plane value. In addition, convective mass transfer was evaluated by using Sherwood number and compared with asymptotic results for laminar convective mass transfer. The resulting Sherwood number closed to asymptotic results almost.
-
宇高 義郎, 大久保 英敏, 荒木 拓人, 酒井 清吾, 浅岡 龍徳, 津島 将司
伝熱 : journal of the Heat Transfer Society of Japan 2012年1月 日本伝熱学会
開催年月日: 2012年1月
記述言語:日本語 会議種別:その他
-
C123 固体酸化物電解質セルを用いた電解システムに関する効率計算(OS5 水素・燃料電池)
水澤 竜也, 武藤 崇史, 荒木 拓人, 森 昌史
動力・エネルギー技術の最前線講演論文集 : シンポジウム 2012年 一般社団法人 日本機械学会
開催年月日: 2012年
記述言語:日本語 会議種別:その他
Solid oxide electrolyte cells are expected to apply for a hydrogen generator as SOECs (Solid Oxide Electrolysis Cells). In this study, we carried out the cycle analysis for SOEC systems. The cycle analysis was carried out by the two following processes. First, we constructed the system models for SOEC systems considering not only SOEC stacks but Balance of Plant (BOP). Next, we calculated for system efficiency based on heat and mass balance. According to the processes, we calculated the SOEC systems by two operating temperatures, 650 and 850℃. As a result, we obtained the high hydrogen energy conversion efficiency (η_<total> =98.4% HHV) of SOEC systems.
-
218105 薄型熱電対を用いたPEFC内の温度場測定(OS11 次世代熱工学,オーガナイズド・セッション)
遠藤 亮将, 宍戸 達哉, 荒木 拓人
日本機械学会関東支部総会講演会講演論文集 2011年 一般社団法人 日本機械学会
開催年月日: 2011年
記述言語:日本語 会議種別:その他
A polymer electrolyte membrane (PEM) is used as electrolyte in polymer electrolyte fuel cell (PEFC). PEM has to be kept moderately moist for the PEM to have the ability to conduct electricity. Moisture content of film depends on the relative humidity of the supply gas. Since relative humidity of the supply gas is changed by the temperature, thermal management is fundamental issue for practical use. To control the temperature and water transport inside the cell, we have to understand the local temperature adjacent to the catalyst layers. In this study, two types of thermocouples electrically insulated by Parylene ware used to measured temperature inside running PEFC cell. As a result cathode temperature was higher than anode and figured out in-situ temperature distribution affected by electric power generation.
-
G203 繊維質多孔体における内部液水分布が伝熱特性に及ぼす影響(OS5 水素・燃料電池)
橘 伸佳, 西田 洋介, 荒木 拓人
動力・エネルギー技術の最前線講演論文集 : シンポジウム 2011年 一般社団法人 日本機械学会
開催年月日: 2011年
記述言語:日本語 会議種別:その他
Polymer Electrolyte fuel cell (PEFC) are comparatively efficient, environmental friendly, and scalable energy converters suitable to a wide range of applications. Heat transport in PEFC is very important to improve cell performance. Especially, heat transport characteristics of gas diffusion layer (GDL) have strong influences on PEFC performance. However, characteristics of GDL for heat transport haven't been figured out yet, clearly. In this study, we measured thermal conductivity in the through-plane direction of GDL varying degree of water content in GDL by steady state method. In addition, we visualized water distribution inside GDL by simultaneous using X-ray radiography. As a result, we found that water distribution and degree of water content inside GDL strongly affect the thermal conductivity of GDL and thermal contact resistance between GDL and standard materials.
-
固体高分子形燃料電池の非定常応答におけるMPLおよび液水輸送の影響
三宅 聡, 洗川 拓也, 山田 賢英, 佐藤 暁, 荒木 拓人
日本伝熱シンポジウム講演論文集 2011年 社団法人 日本伝熱学会
開催年月日: 2011年
記述言語:日本語 会議種別:その他
環境負荷が低く,出力密度が高いことから特に注目されている固体高分子形燃料電池(PEFC)であるが,より広い普及のためにはいくつかの課題が残されている.中でも内部の水分管理は電池性能向上のために重要とされるが,液水が滞留する条件やマイクロポーラス層(MPL)を用いた際の水分,化学種の輸送現象は非常に複雑となり,特にその過渡特性について議論した例は少ない.本研究では実験および数値解析を併用し,液水輸送やMPLが運転条件変化時のセル性能へ与える影響について検討したので報告する.
-
固体高分子形燃料電池MEA内の局所物質輸送と電気化学反応を考慮した非定常数値解析
官林 亮, 阿江 朋暁, 西田 洋介, 荒木 拓人
日本伝熱シンポジウム講演論文集 2011年 社団法人 日本伝熱学会
開催年月日: 2011年
記述言語:日本語 会議種別:その他
固体高分子形燃料電池(PEFC)はクリーンで電気エネルギへの変換効率の高いエネルギ変換装置であり,定置用,自動車用電源として実用化と共に普及が期待されている.しかし,課題は多く残されており,運転時の局所的な物質輸送や,負荷変動に伴う過渡特性について十分な理解がされていないことが挙げられる.そこで本研究ではカソード,アノード両極でのガス種の輸送,固体高分子膜内の水分輸送,電荷輸送と同時に電気化学反応を考慮した数値解析モデルを作成し,定常,非定常状態での物質輸送と発電特性の関係を検討したので報告する.
-
J081034 ガス流路形状及び内部液水状態が繊維質多孔体の伝熱特性に与える影響([J08103]燃料電池(3))
西田 洋介, 橘 伸佳, 太田 公一, 荒木 拓人
年次大会 2011年 一般社団法人 日本機械学会
開催年月日: 2011年
記述言語:英語 会議種別:その他
Polymer electrolyte fuel cells (PEFCs) are comparatively efficient, environmental friendly, and scalable energy converts suitable to a wide range of applications. Heat transport in PEFCs is the important factor to improve PEFCs performance. Especially, heat transport characteristics of gas diffusion layers (GDLs) have strong influence on PEFCs performance. In PEFCs, GDL is contacted separator that has gas channels, which causes a pressure distribution in GDL. Therefore, inner structure of GDL and condition of contact between GDL and separator might be changed. So, teat transport characteristics of GDL will change. Even when liquid water is in GDL, its heat transport characteristics will be change. However, they haven't investigated clearly, yet. In this study, we measured thermal conductivities and thermal resistances of GDLs in the through-plane direction using steady state method, and effects of gas channel geometry and inside water distribution are discussed. We found that contact condition between GDL and separator didn't change GDL-separator thermal contact resistance per unit contact area. And when there is water retention in GDL, we found that water distribution and degree of water content inside GDL influences the thermal conductivity of GDL and GDL-separator thermal contact resistance.
-
J081033 薄膜熱電対を用いたPEFC内温度場測定([J08103]燃料電池(3))
宍戸 達哉, 遠藤 亮将, 荒木 拓人
年次大会 2011年 一般社団法人 日本機械学会
開催年月日: 2011年
記述言語:英語 会議種別:その他
In order to understand water behavior inside polymer electrolyte fuel cell (PEFC), we measured temperature distribution in the cell because the water behavior is impacted largely local temperature. We developed Au-Ni thin film thermocouples fabricated on parylene (poly-para-xylene) layer for measuring the internal temperature distribution of PEFC. This thermocouple was fabricated using micro-electro-mechanical-systems (MEMS) technology. Sputtering technique was employed to deposit a 1pm thick layer of Au-Ni thin film thermocouples on 2p.m thick parylene. Parylene was deposited on 4-inch silicon wafer. Then, the Au-Ni thin film thermocouples were covered with a 2pm parylene layer using deposition apparatus to protect them from environmental degradation. Fabricated thin film thermocouples embedded between the MEA (Membrane Electrode Assembly) and the GDL (Gas Diffusion Layer). The measurement result showed that temperature at cathode catalyst layer was higher than that anode catalyst layer. Insulation of thin film thermocouples has done well. It is necessary to optimize the thermocouples for precise measurement. In order to accurately measure the temperature, it is necessary to optimize the device.
-
J081032 液水輸送を考慮した三次元数値モデルによるPEFC非定常セル性能評価([J08103]燃料電池(3))
佐藤 暁, 洗川 拓也, 三宅 聡, 荒木 拓人
年次大会 2011年 一般社団法人 日本機械学会
開催年月日: 2011年
記述言語:英語 会議種別:その他
Water condition in cell is important to disseminate PEFC extensively. Especially in high current density region, liquid water accumulated inside GDL strongly affects PEFC cell performance and unsteady properties. Considering of liquid water in PEFC has been studied within advanced research, but they had employed isothermal model. Thermal gradient is generated inside PEFC cell, due to activation overpotential, entropy change, and phase change. Thermal gradient strongly affects water condition, because relative humidity is function of temperature. And so we have developed isothermal model and investigated effects on water condition also power generation property. From a result, decreased 3% to 4% in the cell voltage high current density range when compared to the system was extended to non-isothermal isothermal. This increases the internal temperature of the cell as a high current density region will be transferred to the dry state. By comparing the results with the results of experiment at some conditions was to verify the validity of this analysis.
-
供給ガス相対湿度変化がPEFC 発電応答特性へ及ぼす影響
荒木 拓人
機械学会論文集B編 76(771) 2010年
開催年月日: 2010年
記述言語:その他外国語 会議種別:その他
-
微細多孔体内のX線ラジオグラフィーによる液水挙動可視化と酸素拡散特性の同時計測
大徳 忠史, 荒木 拓人, 近藤 俊介, 大森 康由, 太田 公一, 金子 春樹, 上杉 健太朗, 宇高 義郎
日本伝熱シンポジウム講演論文集 2010年 社団法人 日本伝熱学会
開催年月日: 2010年
記述言語:日本語 会議種別:その他
ガス拡散層(GDL)など微細多孔体内の液水挙動と酸素拡散特性の関係を解析して,そのメカニズムを明らかにすることは,PEFCの性能向上,コスト低減を効率的に実現する上で必須である.本研究では,酸素拡散特性の測定中にはGDL中の液水が蒸発し,時々刻々と液水の分布が変化する過程において,3次元X線CT可視化手法によるGDL中の液水分布測定とガルバニ電池を用いた酸素拡散特性の同時計測を試みた.
-
含水時の炭素繊維質多孔体の熱伝導率測定とPEFC内局所温度測定
遠藤 亮将, 荒木 拓人, 大洞 健治, 橘 伸佳
日本伝熱シンポジウム講演論文集 2010年 社団法人 日本伝熱学会
開催年月日: 2010年
記述言語:日本語 会議種別:その他
供給ガスの相対湿度や生成水の蒸発,凝縮などの観点から,PEFCにおいてセル内部の温度分布を把握することは,電解質である固体高分子膜(PEM)の適度な湿潤を保つために必要不可欠である.しかし,現時点ではPEFCを構成する各部材の熱物質特性についての十分な知見があるとは言えない.そこで本研究では,PEFCを構成する部材の一つであるGDLの熱伝導率を測定した.また,市販されている極細熱電対に絶縁処理を行い運転中の燃料電池内に挿入することで,セルの運転時の内部温度の分布を測定した.
-
供給ガス相対湿度変化がPEFC発電応答特性へ及ぼす影響(熱工学,内燃機関,動力など)
眞鍋 壮, 上村 有輝, 荒木 拓人
日本機械学会論文集B編 2010年 一般社団法人 日本機械学会
開催年月日: 2010年
記述言語:日本語 会議種別:その他
Polymer Electrolyte Fuel cell (PEFC) gained wider interest as a clean and efficient energy conversion device. Proper water management is needed, because vapor and liquid transport effects strongly on PEFC power generation characteristics and efficiency. However, water transport factors have not been well understood especially during unsteady operation, which is often observed in uses of vehicles or distributed stationary power generators. In this paper, to grasp and generalized effects of the local water transport on the PEFC performance, we have developed unsteady numerical model considering water transports and compared its calculated results with experimental responses to verify the model adequacy and discuss water transport factors. In the numerical model, mass conservation equations and charge conservation equations in gas channel, GDL and MEA were solved. As necessary parameters for developing them, we measured membrane resistivity, activation over-voltage etc by ourselves. The membrane resistivity increases extremely as relative humidity decrease, and activation over-voltage is also affected by relative humidity, not only by current density and oxygen activity. The measured and calculated transient responses were agreed well in most operating conditions, then adequacy of our measurement methods of water transport properties and numerical model have been confirmed. Then, we have discussed the effects of transport resistance at MEA surfaces on PEFC transient power generation.
-
G0801-2-3 ガス拡散層内の液水滞留を考慮したPEFC非定常応答解析(動力エネルギー部門一般(2))
洗川 拓也, 真鍋 壮, 荒木 拓人
年次大会講演論文集 2009年 一般社団法人 日本機械学会
開催年月日: 2009年
記述言語:日本語 会議種別:その他
Polymer Electrolyte Fuel Cell (PEFC) is expected to be used in many fields as future power sources. Polymer electrolyte membrane, which is inserted in PEFC as a electrolyte, has proton conductivity that depends on its water content. It is important for improving the cell performance to keep suitable wet condition within the cell and grasp water concentration, diistribution, and its effect. It is said that the voltage response of PEFC is effected by condensed water, so in this study, we predicted the voltage response at the conditions with/without condensed water, and compared the results with experimental data. Both numerical and experimental results had relatively good agreement, and appropriateness of analytical model might be comfirmed.
-
G0801-2-4 ガス拡散層の熱物質輸送特性(動力エネルギー部門一般(2))
大洞 健治, 太田 公一, 遠藤 亮将, 荒木 拓人
年次大会講演論文集 2009年 一般社団法人 日本機械学会
開催年月日: 2009年
記述言語:日本語 会議種別:その他
The heat and mass transport characteristics of gas diffusion layer have strong influence on Polymer Electrolyte Fuel Cell (PEFC) performance. In this study, we measured thermal conductivity of GDL by steady state method and discussed about diffusive characteristics of GDL. Little difference was observed in diffusive resistances of GDL with or without PTFE. Measured diffusive resistances can be organized by (u/l)^<0.5>
-
膜電極接合体界面の輸送抵抗がPEFC非定常発電特性に及ぼす影響
眞鍋 壮, 上村 有輝, 大洞 健治, 荒木 拓人, 恩田 和夫
日本伝熱シンポジウム講演論文集 2009年 社団法人 日本伝熱学会
開催年月日: 2009年
記述言語:日本語 会議種別:その他
PEFC運転条件変化時にはPEFC内部の水分状態が著しく変化するため、PEFC電池性能を向上させる上で水分管理を把握する必要がある。また、PEFC構成部材である膜電極接合体(MEA)とガス拡散層(GDL)の界面には、Micro Porous Layer(MPL)や触媒層のカーボン粒が存在し、熱物質輸送特性に影響を及ぼしている。本稿では、実験と解析を用いてMEA-GDL界面の熱物質輸送特性が非定常発電特性に及ぼす影響について検討したので報告する。
-
J0601-2-3 カソード触媒層内の酸素拡散がPEFC発電特性に及ぼす影響(燃料電池システムおよび熱・物質移動)
阿江 朋暁, 上村 有輝, 荒木 拓人
年次大会講演論文集 2009年 一般社団法人 日本機械学会
開催年月日: 2009年
記述言語:日本語 会議種別:その他
Cathode Catalyst Layer (CCL) is very important part that has strong effect on the performance of Polymer Electrolyte Fuel Cell (PEFC). In this study, we have developed one-dimensional, steady state, isothermal model of a fuel cell consisting of Polymer Electrolyte Membrane (PEM), CCL and Gas Diffusion Layer (GDL). In addition, we have considered agglomerates in CCL and we divided CCL into three regions, which have different porosity respectively, to discuss effects of oxygen diffusion and ionic conductivity on electrical generating performance. It was found that the distribution of CCL porosity may have big influence on the PEFC power generating characteristics.
-
燃料電池のなかの熱物性問題
荒木 拓人
熱物性 : Japan journal of thermophysical properties 2008年8月
開催年月日: 2008年8月
記述言語:日本語 会議種別:その他
-
2119 供給ガス湿度変化時のPEFC発電特性解析(J17-3 燃料電池(3) 固体高分子形燃料電池,ジョイントセッション,21世紀地球環境革命の機械工学:人・マイクロナノ・エネルギー・環境)
上村 有輝, 眞鍋 壮, 荒木 拓人, 長濱 光幸, 恩田 和夫
年次大会講演論文集 2008年 一般社団法人 日本機械学会
開催年月日: 2008年
記述言語:日本語 会議種別:その他
Proton conductivity of polymer electrolyte membrane (PEM), which is used as electrolyte of the PEFC, depends on water content of PEM. It is very difficult to measure local water transport phenomena, so we use numerical analysis to grasp this effect. In this study, the effect of water in a PEFC was discussed by comparing experimental results with analytical results, which were conducted by unsteady two-dimensional model. Analytical results showed good agreement with experimental results of voltage response after sudden supplied gas humidity change for the conditions without flooding. In addition to these study, by calculating humidity distributions in a PEFC, we illustrated the relationship between water content of PEM and cell voltage.
-
固体高分子形燃料電池内の熱物質輸送特性
眞鍋 壮, 上村 有輝, 長濱 光幸, 荒木 拓人, 恩田 和夫
日本伝熱シンポジウム講演論文集 2008年 社団法人 日本伝熱学会
開催年月日: 2008年
記述言語:日本語 会議種別:その他
固体高分子形燃料電池(PEFC)内部の温度が変化すると,相対湿度に依存する膜の湿潤状態も変化する.膜電極接合体(MEA)では局所的な発熱や乾燥が起きていると考えられ,燃料電池の性能低下や膜劣化の要因となる可能性がある.そこで本研究では,同じ露点温度で加湿されたガスをセルに供給し,両極に温度差を付けた時の熱物質輸送を熱電対,露点計を用いて測定した.その結果,供給ガスの水分量が同じにも関わらず,セル両極において低温側から高温側への水移動が観測された.
-
固体高分子形燃料電池における物質輸送と非定常発電特性
荒木 拓人, 真鍋 壮, 上村 有輝, 恩田 和夫
電気学会研究会資料. FTE, 新エネルギー・環境研究会 2007年12月
開催年月日: 2007年12月
記述言語:日本語 会議種別:その他
-
固体高分子燃料電池の電流分布の測定と解析
長濱 光幸, 乾 義尚, 荒木 拓人
電気学会研究会資料. FTE, 新エネルギー・環境研究会 2007年9月
開催年月日: 2007年9月
記述言語:日本語 会議種別:その他