研究者詳細 - 梅澤　修

論文 - 梅澤　修

件数 229 件

Influence of prior quenching and tempering treatment on cementite formation during nitriding at 913 K for SCM440 steel

Minheon Kim, Osamu Umezawa

ISIJ International 65 ( 7 ) 2025年6月 [査読有り]

記述言語：英語掲載種別：研究論文（学術雑誌）単著

Effects of β phase and initial dislocation density on dwell fatigue deformation and crack initiation mechanism in Ti-5Al-2Fe-3Mo alloy

Daiki Miyashita, Yusuke Nakao, Osamu Umezawa

Materials Science and Engineering A 924 147852 2025年2月 [査読有り]

DOI

担当区分：責任著者記述言語：英語掲載種別：研究論文（学術雑誌）共著

すべりを伴う転動疲労におけるSCM440H窒化材の化合物層中ポア形状の変化と耐ピッチング強度への影響

丸山貴史, 梅澤　修

鉄と鋼 111 ( 2 ) 32 - 40 2025年2月 [査読有り]

DOI CiNii Research

記述言語：日本語掲載種別：研究論文（学術雑誌）出版者・発行元：一般社団法人日本鉄鋼協会共著

Nitriding is a beneficial surface hardening heat treatment to reduce CO2 emissions and shows a potential partially replace carburized steels adopted for sliding parts such as bearings and gears. Both the bending fatigue strength and pitting fatigue strength under high contact pressure were evaluated for nitrided JIS-SCM440H materials using two types of controlled-nitridings, i.e. γ' and e, and conventional gas nitriding. Not only the thickness of the compound layer but also its phase structure such as γ' and e significantly affected the 107 cycles bending fatigue strength, where the γ'-nitrided material was the highest. On the other hand, almost no effects of the thickness and phase structure on the 107 cycles pitting fatigue strength were detected in the materials. Compared to the carburized material, the γ'-nitrided material exhibited higher 107 cycles fatigue strength in bending and pitting, but poor fatigue strength in the lower cycles range. The shape and size of the pores in the compound layer were altered during roller-pitching tests, although there was almost no reduction in the thickness of the compound layer. The pore size was reduced by pore closure, especially at higher contact pressures. Pore closure was more pronounced in the γ'-nitrided materials than in the ε-nitrided materials at lower contact pressures. The 107 cycles pitting fatigue strength was improved after the pore closure, resulting from fewer defects.

Influence of carbonitriding and sub-zero treatment on the microstructure and fatigue strength of JIS-SCM420 low-alloy steel

Minheon Kim, Osamu Umezawa

Materials Science and Engineering A 923 147751 2025年2月 [査読有り]

DOI

記述言語：英語掲載種別：研究論文（学術雑誌）共著

Role of dislocation characteristics on deformation behavior of martensitic steel analyzed by neutron diffraction

Dannoshita Hiroyuki, Hasegawa Hiroshi, Higuchi Sho, Matsuda Hiroshi, Gong Wu, Kawasaki Takuro, Harj … 全著者表示

Proceedings of International Symposia on Steel Science 2024 ( 0 ) 209 - 212 2024年11月

DOI CiNii Research

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）出版者・発行元：一般社団法人日本鉄鋼協会共著

The deformation behavior of lath martensite has been extensively explored, with this study focusing on its characteristics through the lens of dislocation theory. We conducted an in-situ neutron diffraction study to investigate the tensile deformation behavior of ultra-low carbon Fe–18Ni alloy under different heat treatment conditions. These alloys were initially quenched and then tempered at 573 K and 773 K. This study aimed to quantitatively evaluate dislocation characteristics and understand their role in the resulting stress–strain curves. To achieve this, we applied the convolutional multiple whole profile (CMWP) method, which determines the microstructural parameters from diffraction line profiles, linking macroscopic deformation behavior with quantitative information on dislocation characteristics without relying solely on local information. The CMWP method evaluates the dislocation characteristics, such as density, arrangement, and character. Our findings revealed that a high dislocation density in the quenched state, which gradually decreased with increasing tempering temperature, affected the mechanical properties such as the tensile strength. Additionally, we closely monitored also changes in the arrangement and character of dislocations as tempering temperature increased and during deformation. The parameters played a crucial role in revealing the evolution of flow stresses.

中間熱処理を施した7%Ni鋼の極低温靭性に及ぼすMnの影響

佐藤祐也, 橘俊一, 西山武志, 真玉橋力也, 梅澤修, 田川哲哉

鉄と鋼 110 ( 11 ) 871 - 879 2024年9月 [査読有り]

DOI CiNii Research

記述言語：日本語掲載種別：研究論文（学術雑誌）出版者・発行元：一般社団法人日本鉄鋼協会共著

The effect of the manganese content of 7 % nickel-added steel on cryogenic toughness was investigated. When Charpy absorbed energy was investigated in the steels with wide range manganese content from 0.05 % to 2.16 %, the absorbed energy at −196 °C increased with a decrease of manganese content. The two steels with manganese contents of 0.2 % and 0.8 % were selected for use in a more detailed investigation regarding the dependence of toughness at −196 ℃ on the intermediate heat treatment temperature, fracture behaviors and the retained austenite. Although the 0.2 % manganese steel stably exhibited a high absorbed energy at −196 ℃ at all intermediate heat treatment temperatures examined in this work, it was necessary to select an appropriate intermediate heat treatment temperature for the 0.8 % manganese steel in order to　achieve high absorbed energy at −196 ℃. The total amount of the retained austenite and the size and the nickel content locally segregated into an identical retained austenite were quantified by using XRD and SEM/EDS, and the characteristics of the retained austenite in the steels with low manganese alloy designs were investigated. The cleavage-type brittle fracture that appeared in some specimens was discussed from the viewpoint of the stability of retained austenite.

Understanding crack growth within the γ’ Fe4N layer in a nitrided low carbon steel during monotonic and cyclic tensile testing

Rama Srinivas Varanasi, Motomichi Koyama, Mizuho Yokoi, Yusuke Ootani, Momoji Kubo, Kento Tanahara, … 全著者表示

Journal of Materials Science 59 14639 - 14652 2024年7月 [査読有り]

DOI

記述言語：英語掲載種別：研究論文（学術雑誌）共著

Strength and fracture toughness of type 304 and 316 austenitic stainless steels at 4.2 K

Takeru Sakurai, Osamu Umezawa, Yoshinori Ono

IOP Conference Series: Materials Science and Engineering 1302 012002 2024年7月 [査読有り]

DOI

担当区分：責任著者記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）単著

High-cycle fatigue strength of 22Cr-12Ni austenitic stainless steel at 77 K

Muhammad Edgar Bratasena, Tetsuya Kato, Osamu Umezawa, Yoshinori Ono, Masayuki Komatsu

IOP Conference Series: Materials Science and Engineering 1302 012001 2024年7月 [査読有り]

DOI

担当区分：責任著者記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）単著

{001}<101> texture evolution by preferential dynamic grain growth in Ti-37 mol%Nb alloy under plane strain compression at high temperatures

Umezawa Osamu, Hayakawa Yujiro, Schindler Ivo, Fukutomi Hiroshi

MATERIALS TRANSACTIONS 65 ( 3 ) 282 - 291 2024年3月 [査読有り]

DOI CiNii Research

担当区分：筆頭著者,　責任著者記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：公益社団法人日本金属学会共著

{001}〈101〉 texture evolution in Ti–37 mol%Nb (Nb–46.5 mass%Ti) alloy was determined under plane strain compression at the temperatures of 800°C, 950°C, and 1100°C, in which preferential dynamic grain growth (PDGG) took place. At lower temperature and higher strain rate such as 800°C–10−2/s, almost no grain growth occurred in the transverse direction (TD), and the α-fiber + near {111}〈110〉 in the γ-fiber texture was developed, which was a stable orientation as deformation texture. At higher temperature and lower strain rate such as 1100°C–10−3/s, the grain growth along the TD remarkably appeared by grain boundary bulging, and an extremely high pole density of the texture near the α-fiber, especially the rotated cube {001}〈101〉, evolved. A planar dislocation structure with pile-ups appeared and individual dislocations were uniformly distributed in the grains. The rotated cube texture fulfills the conditions of the deformation stability and the low Taylor factor in accordance with the PDGG mechanism. The essential aspect of the mechanism is the preferential growth of grains with a stable orientation for deformation and a low Taylor factor in the given deformation mode.

High-strength and high-toughness austenitic stainless steels based on type 316LN at 4.2 K

Takeru Sakurai, Osamu Umezawa,

Cryogenics 136 103762 - 103762 2023年12月 [査読有り]

DOI CiNii Research

記述言語：英語掲載種別：研究論文（学術雑誌）単著

Effects of dislocation arrangement and character on the work hardening of lath martensitic steels

Hiroyuki Dannoshita, Hiroshi Hasegawa, Sho Higuchi, Hiroshi Matsuda, Wu Gong, Takuro Kawasaki, Stef … 全著者表示

Scripta Materialia 236 115648 2023年11月 [査読有り]

DOI Web of Science CiNii Research

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：Elsevier 単著

Work-hardening behavior of a lath martensitic Fe–18Ni alloy during tensile deformation is discussed based on the Taylor's equation. The dislocation characteristics are monitored using in situ neutron diffraction. In the specimens of as-quenched (AQ) and tempered at 573 K (T573), the dislocations are extremely dense and randomly arranged. The dislocations in AQ and T573 form dislocation cells as deformation progresses. Consequently, a composite condition comprising cell walls and cell interiors is formed, and the coefficient α in the Taylor's equation increases. Cells are already present in the specimen tempered at 773 K (T773), which has a low dislocation density and a large fraction of edge-type dislocations. As deformation continues, the dislocation density of T773 increases, its cell size decreases, and its composite condition become stronger. Simultaneously, the edge-type dislocation fraction decreases, keeping α unchanged. Thus, both the dislocation arrangement and character affected α, thereby affecting the work-hardening behavior.

High-Temperature Hardness in Hypereutectoid Steels with Various Microstructures Measured by Using Small Ball Rebound Hardness Test

Koga Norimitsu, Koizumi Kouki, Takayasu Shuto, Umezawa Osamu, Watanabe Mizuki, Yamamoto Masayuki, Y … 全著者表示

MATERIALS TRANSACTIONS 64 ( 7 ) 1600 - 1604 2023年7月 [査読有り]

DOI Web of Science CiNii Research

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：公益社団法人日本金属学会共著

The temperature dependence of hardness in hypereutectoid steels with various microstructures was measured by using the small ball rebound hardness test, and the effect of carbon state on the high-temperature hardness was discussed. As-received and spheroidized cementite steels consisted of spheroidized cementite, graphite and ferrite matrix, and the volume fraction of graphite in the spheroidized cementite steel was larger than that in the as-received steel. Pearlite steel had ferrite and cementite lamellar structure without graphite. The characteristic hardening was detected above 700 K in all steels, suggesting that the solid solute carbon enhances the hardness even in hypereutectoid steels with high strength. The pearlite steel exhibited the highest hardness owing to the ferrite and cementite lamellar structure and no graphite. While the spheroidized cementite steel exhibited the lowest hardness, although the size of cementite was finer than that in the as-received steel. It was quantitatively demonstrated that the large volume fraction of graphite caused the low hardness in the spheroidized cementite steel.

Fracture toughness and martensitic transformation in type 316LN austenitic stainless steel extra-thick plates at 4.2 K

Takeru Sakurai, Osamu Umezawa

Materials Science and Engineering A 862 144122 - 144122 2023年1月 [査読有り]

DOI Web of Science CiNii Research

記述言語：英語掲載種別：研究論文（学術雑誌）単著

Electrochemical, biological and technological properties of anodized titanium for color coded implants

Josef Hlinka, Kamila Dostalova, Kristina Cabanova, Roman Madeja, Karel Frydrysek, Jan Koutecký, Zuz … 全著者表示

Materials 16 ( 2 ) 632 2023年1月 [査読有り]

DOI Web of Science PubMed

記述言語：英語掲載種別：研究論文（学術雑誌）単著

Effects of vanadium addition on strain distribution, crack initiation and propagation during low-cycle fatigue test in ferrite and martensite dual-phase steel

Norimitsu Koga, Akihiro Kaseya, Osamu Umezawa, Hiroshi Nakata, Shunsuke Toyoda

ISIJ International 62 ( 10 ) 2132 - 2134 2022年10月 [査読有り]

DOI Web of Science CiNii Research

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：一般社団法人日本鉄鋼協会単著

Effects of vanadium (V) addition on strain distribution, crack initiation and propagation behavior during low-cycle fatigue test in ferrite and martensite dual phase (DP) steel were revealed. V addition effectively extended the low-cycle fatigue life, even though the tensile properties were approximately identical between V-added DP and DP steels. The stress amplitude suddenly decreased just before fracture in the V-added DP steel. The fatigue crack initiated from the surface and propagated inside, and the brittle fracture occurred in the crack propagation region in the V-added DP steel. The strain distribution introduced during the low-cycle fatigue test was more inhomogeneous for the V-added DP steel than that for the DP steel, and the fatigue crack was generated from the high-strain region. Considering that the number of cycles for crack initiation in the V-added DP steel was larger than that in DP steel, the inhomogeneous strain distribution in the V-added steel promoted crack nucleation but suppressed crack growth in the crack initiation stage. Cracks propagated independent of the strain distribution in the V-added DP steel in the crack propagation stage. The crack propagation rate in the V-added DP steel was remarkably higher than that in DP steel in the crack propagation stage. Thus, V addition effectively extended the number of cycles for crack initiation but caused brittle fracture and faster crack propagation.

Evolution of dislocation structure determined by neutron diffraction line profile analysis during tensile deformation in quenched and tempered martensitic steels

Hiroyuki Dannoshita, Hiroshi Hasegawa, Sho Higuchi, Hiroshi Matsuda, Wu Gong, Takuro Kawasaki, Stef … 全著者表示

Materials Science and Engineering A 854 143795 2022年9月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）単著

Tribofilm properties and microcrack morphologies for a carburized SCM420 steel under high-pressure rolling sliding contact fatigue with lubricants containing high sulfur- and phosphorus-additives

Takayasu Shuto, Umezawa Osamu, Hashimoto Kazuya

WEAR 502-503 204397 2022年8月 [査読有り]

DOI CiNii Research

担当区分：責任著者記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：Elsevier Science SA 共著

Tribofilms and microcracks developed on a carburized SCM420 steel through a two-roller-type pitting test were characterized. Tribofilms composed mainly of calcium phosphate, iron phosphate, and iron oxide were generated on the contact surface. The tribofilms were homogeneously distributed on the contact surfaces that exhibited a longer life, suggesting that the tribofilm distribution affects the rolling sliding contact fatigue (RCF) life. Compounds including the elements from the lubricant were also generated on the surfaces of microcracks formed on the contact surface, suggesting that lubricant flowed into the surface microcracks during the test. The martensitic microstructure at the specimen subsurface was dynamically reconstructed to an ultrafine-grained microstructure during RCF, which resulted in the residual stress relief, especially on the contact surface. After the residual stress release, the fluid pressurization accelerated the formation of a mixed-mode microcrack of mode I and mode II with a high angle to the surface in the later stage, while a shallow microcrack in mode II developed during the early stage.

Tensile properties of 22Cr-12Ni austenitic stainless steel thick plates and bars at cryogenic temperatures

Tetsuya Kato, Yoko Kato, Osamu Umezawa, Yoshinori Ono, Arata Nishimura, Susumu Kumagai, Tetsumi Yuri

IOP Conference Series: Materials Science and Engineering 1241 012001 2022年6月 [査読有り]

DOI

担当区分：責任著者記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Effects of grain size and strain rate on the low-temperature tensile properties of ferrite-austenite duplex stainless steel

N. Koga, T. Namiki, O. Umezawa

IOP Conference Series: Materials Science and Engineering 1241 012002 2022年6月 [査読有り]

DOI

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Statistical Analysis of Influential Factors on the Stability of Retained Austenite in Low Alloy TRIP Steel

Koga Norimitsu, Yamashita Takayuki, Ogawa Keisuke, Umezawa Osamu

MATERIALS TRANSACTIONS 63 ( 5 ) 693 - 702 2022年5月 [査読有り]

DOI Web of Science CiNii Research

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：公益社団法人日本金属学会共著

The factors representing the stability of retained austenite (γR) in low-alloy TRIP steel at a plastic strain of up to 0.04 were statistically analyzed by evaluating the size, strain level, crystal orientation, morphology, and precipitation site of a large number of γR grains (>1000). The ratio (Rarea) of the area of γR after deformation to that before deformation was adopted as a representative parameter for the stability of γR. The frequency of low Rarea in fine γR was significantly high, indicating that they were unstable. Moreover, it was indicated that γR in the high-strain regions tended to be unstable, whereas γR in the bainite region was stable. The crystal orientation and aspect ratio did not correlate with Rarea in TRIP steel. The strain level and precipitation sites in coarse γR were uncorrelated with Rarea, indicating that the size of the γR has a greater effect on its stability. The stability of γR was not dominated by the carbon concentration but was affected by other factors. The size of γR may represent the stress conditions at the γR/ferrite or bainite boundaries, which is why this factor represents the stability of γR in the TRIP steel at a plastic strain of up to 0.04.

Deformation structure around a crack in γ’-Fe4N layer of nitrided extra-low carbon steel subjected to cyclic tensile test

Norimitsu Koga, Kento Tanahara, Osamu Umezawa

Metallurgical and Materials Transactions A 53 ( 4 ) 1150 - 1155 2022年4月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）共著

Effects of crystallographic texture on subsurface fatigue crack generation in Ti-Fe-O alloy at low temperature

Osamu Umezawa, Weibo Li

ISIJ International 62 ( 3 ) 593 - 601 2022年3月 [査読有り]

DOI Web of Science CiNii Research

担当区分：筆頭著者記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：一般社団法人日本鉄鋼協会共著

Subsurface microcracks developed in a groove-rolled and cold-swaged Ti–Fe–O alloy were characterized to clarify the generation of subsurface fatigue crack. In addition, the effects of crystallographic texture on subsurface crack initiation and growth were discussed. A considerable number of microcracks were detected in the β grains, α grains, and at the α-β interface. The microcracks in the β grains grew negligibly into the neighboring α grains along the basal plane. This was because these grains were oriented with their c-axis almost perpendicular to the loading axis. The {10 10}α fiber texture prevents the formation of basal facet and its growth on the basal plane. The stress concentration around the microcrack in the β grains could assist the growth of the microcrack into neighboring α grains along the prismatic plane (which is inclined to the loading axis at a suitable angle) or occasionally at a {10 10}α twist boundary. The {10 10}α fiber texture assisted microcrack growth, and thereby, formed aligned facets and yield longer microcrack length. The combination of the shear stress and opening stress on {10 10}α results in a Mode II or III microcrack and causes microcrack growth on the prismatic plane in the neighboring grain.

Crystal plasticity analysis of temperature-sensitive dwell fatigue in Ti-6Al-4V titanium alloy for an aero-engine fan disc

Yin Liangwei, Umezawa Osamu

International Journal of Fatigue 156 106688 2022年3月 [査読有り]

DOI CiNii Research

担当区分：責任著者記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：Elsevier Science Ltd. 共著

This study investigates the temperature-dependent dwell fatigue behavior of Ti-6Al-4V alloy using crystal plasticity finite element method. The dislocation mechanism-based crystal plasticity parameters are calibrated with the data of quasi-static tensile and constant load creep tests at ambient and intermediate temperatures. In particular, the rate-dependent parameters related to slip property are employed to establish the relationship between strain rate sensitivity of a soft alpha-titanium single crystal and temperature. The variation of strain rate sensitivity with temperature influences the stress redistribution occurring within the hard-soft grain combination, which in turn affects the dwell fatigue sensitivity. Further, the structural analysis for a Ti-6Al-4V fan disc provides the stress fields at takeoff and cruise phases to examine the in-service stress redistribution. The highly localized hoop stress and presence of large macrozones at the bore of the fan disc, rather than the fair rate sensitivity of soft macrozones at working temperatures, are responsible for triggering basal stress enhancement and dwell facet nucleation in hard macrozones.

Visualization of strain distribution around fatigue crack introduced by low-cycle fatigue test in high-strength steels using digital image correlation method for replica films

Norimitsu Koga, Yuta Sakamaki, Akihiro Kaseya, Osamu Umezawa, Hiroshi Nakata, Shunsuke Toyoda

Materials Characterization 185 111731 2022年3月 [査読有り]

DOI Web of Science CiNii Research

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：Elsevier 共著

Strain distributions around the fatigue crack during the low cycle fatigue of high-strength ferrite + martensite dual-phase (DP) and tempered martensite (Mt) steels were visualized during cycles from the initial state to the crack initiation and crack propagation using a digital image correlation analysis applied to replica films. The replica film successfully transcribed the microstructure on the specimen surface. Although both the DP and Mt. steels exhibited a high tensile strength, the work-hardening rate of the DP steel was higher than that of Mt. steel. Although the numbers of cycles to failure (Nf) in the DP and Mt. steels were almost the same at the total strain amplitudes (εt) of 0.005–0.008 and 0.02–0.03, the Nf in the DP steel was higher than that in the Mt. steel at the εt of 0.008–0.02. The cracks were generated and propagated along the high-tensile-strain regions in both steels and were initiated when the accumulated strain along the loading direction exceeded a critical value regardless of the value of εt or the steel applied. The increment of the accumulated strain in the Mt. steel was higher than that of the DP steel at the εt of 0.01, whereas it was almost the same between those at the εt of 0.03. The inhomogeneity of the strain distribution, which was quantitatively evaluated from the histogram of the strain distribution, increased as the number of fatigue cycles increased. The strain was rather inhomogeneously introduced in the Mt. steel in comparison to the DP steel at the εt of 0.01, whereas almost no difference in the inhomogeneity of the strain distribution was detected between the steels at the εt of 0.03. Thus, the inhomogeneous strain distribution may promote crack initiation and propagation, resulting in a low Nf at the εt of 0.008–0.02 in Mt. steel.

Study on development policy for new cryogenic structural material for superconducting magnet of fusion reactor

Arata Nishimura, Yoshinori Ono, Osamu Umezawa, Susumu Kumagai, Yohko Kato, Tetsuya Kato, Tetsumi Yu … 全著者表示

Nuclear Materials and Energy 30 101125 2022年3月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）共著

The preferential dynamic grain growth mechanism enabling the control of microstructure and texture by high temperature deformation: experimental evidence and applicability

Hiroshi Fukutomi, Kazuto Okayasu, Yusuke Onuki, Makoto Hasegawa, Equo Kobayashi, Bohumir Strnadel, … 全著者表示

Materials Transactions 63 ( 2 ) 148 - 156 2022年1月 [査読有り]

DOI Web of Science CiNii Research

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：公益社団法人日本金属学会共著

The relationship between the mechanism of high temperature deformation and the evolution behavior of microstructure and the texture during deformation, which has been found in various solid solution alloys, is clarified. It is shown that the preferential dynamic grain growth (PDGG) mechanism proposed by the authors can explain the behavior of microstructure change as well as texture change of all studied alloys without contradiction. The essential aspect of the PDGG mechanism is the preferential growth of crystal grains with the orientation stable for deformation and with low Taylor factor in the given deformation mode. It is concluded that the Taylor factor corresponds to dislocation density and stored energy during the high temperature deformation of solid solution alloys when viscous glide of dislocations is the rate controlling process. The possibility of the occurrence of the PDGG mechanism in materials other than solid solution alloys is also discussed.

Crack initiation and propagation behavior in γ’-Fe4N layer during monotonic and cyclic tensile deformation in the nitrided ultra-low carbon steel

Norimitsu Koga, Susumu Saito, Osamu Umezawa

Journal of Materials Science 57 ( 3 ) 2194 - 2207 2022年1月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）共著

SCM420浸炭鋼の高面圧・すべり環境下における転がり疲労過程

橋本和弥, 渕上太一, 鑓恵介, 梅澤修

鉄と鋼 108 ( 1 ) 76 - 87 2022年1月 [査読有り]

DOI Web of Science CiNii Research

記述言語：日本語掲載種別：研究論文（学術雑誌）出版者・発行元：一般社団法人日本鉄鋼協会共著

It is important to improve fatigue life for pitting of gear in order to attempt down-sizing of gear unit and low fuel consumption. Rolling and sliding contact fatigue under high pressure in carburized SCM420 steel is studied. The ultimate aim is to understand the effect of material properties on the fatigue life. In this research, there was considerable interest in change of the material in the contact surface of specimens depending on the shift in tangential force acting on a moving roller in the direction of a tangent to the path of the roller during the fatigue test. Three lubricants were used in these fatigue tests for the purpose of changing the degree of tangential force. A roller tested under a lubricant that the tangential force is shifted higher compared with that of the other lubricant produced a pitting failure earlier. The roller also promoted to decrease the hardness and to narrow the half width of the (211) peak of alpha iron at the contact surface. The transition of these characteristics related to the creation of fine grain layer. That is regarded as worked structure formed during fatigue process. The depth of fine grain layer expands according to repeated loading. Fatigue crack propagation depth was almost equal to the depth of fine grain layer. Not only well-known softening caused by increase in temperature but also microstructural change caused by repeated stress loading have an effect on the life through the involvement in fatigue crack initiation and propagation behavior.

Influence of dispersed β phase on local deformation pattern in mill-annealed Ti-Fe-O alloy under dwell fatigue loading

Yin Liangwei, Umezawa Osamu

International Journal of Fatigue 152 106447 2021年11月 [査読有り]

DOI CiNii Research

担当区分：責任著者記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：Elsevier Sci Ltd 共著

Grain-scale dwell fatigue behavior in Ti-Fe-O alloy is elucidated, with attention focused on the stress redistribution phenomenon that occurs within the soft-hard grain combination. Elastoplastic properties of the beta phase are determined using nanoindentation and crystal plasticity modeling. On this basis, the role of intergranular beta lath on stress redistribution is evaluated. Redistribution of stress from the soft to hard alpha grain is inhibited in the presence of intergranular beta lath during dwell period. Meanwhile, the peak stress in the beta lath is enhanced. This may result in the competition of two dwell fatigue failure modes at high stress state.

Effect of Aging on Low-temperature Tensile Properties of Ultra-low Carbon Steel

Koga Norimitsu, Kanehira Yuki, Huyen Pham Thi Thanh, Hori Kazuya, Umezawa Osamu

ISIJ International 61 ( 8 ) 2308 - 2316 2021年8月 [査読有り]

DOI Web of Science CiNii Research

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：一般社団法人日本鉄鋼協会共著

The microstructural changes and low-temperature tensile properties of ultra-low carbon steel aged at 443 K were examined, and the relationship between the low-temperature tensile properties and ultra-low carbon state was discussed. Fine cementites of approximately 60 nm were observed at 0.6 ks and coarsened to approximately 800 nm at 600 ks. The yield and tensile stresses at 77 K increased until 6 ks and then decreased. The nominal stress-strain curves of all the specimens at 77 K exhibited low elastic limits, the nominal stress plateaued from an approximate nominal strain of 0.002 and, subsequently, work hardening occurred. In the unaged and 6 ks aged specimens, several twins were generated after the elastic limit, and which increased dramatically in the nominal stress plateau regime, and corresponded to macroscopic yielding. In contrast, the number of twins in the 600 ks aged specimen negligibly increased during macroscopic yielding. Macroscopic yielding occurred in the unaged and 6 ks aged specimens by deformation twinning, while in the 600 ks aged specimen it occurred by slip deformation. In the 6 ks aged specimen, the fine cementites and/or decrease in solid solute carbon enhanced the critical resolved shear stresses of deformation twinning, resulting in the highest strength. In the 600 ks aged specimen, the coarse cementites negligibly enhanced the critical resolved shear stress for slip deformation. Hence, the strength of the specimen aged for 600 ks decreased as compared to the specimen aged for 6 ks, and slip deformation occurred.

その他リンク： https://ci.nii.ac.jp/naid/130008075184

Microstructural evolution in Ti-37 mol%Nb alloy under uniaxial compression at high temperatures

Yujiro Hayakawa, Osamu Umezawa

Journal of Alloys and Compounds 871 159603-1 - 159603-11 2021年8月 [査読有り]

DOI Web of Science

担当区分：責任著者記述言語：英語掲載種別：研究論文（学術雑誌）共著

Spectroscopy analyses of tribofilm and surface microcracks in carburized SCM420 steel under high-pressure rolling contact fatigue

Takayasu Shuto, Umezawa Osamu, Yari Keisuke, Hashimoto Kazuya, Fuchigami Taichi

WEAR 477 203807 2021年7月 [査読有り]

DOI CiNii Research

担当区分：責任著者記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：Elsevier Science SA 共著

The tribofilm and surface microcracks developed on a carburized SCM420 steel through a two-roller-type pitting test were characterized. A streaky 100- to 200-nm-thick tribofilm was generated on the specimen surface after 1.0 x 105 cycles. The tribofilm was identified to be mainly composed of calcium phosphate Ca3(PO4)2 and iron phosphate Fe3(PO4)2. Microcracks having lengths of a few tens of micrometers were detected on the contact surface without the tribofilm after the test. The number of cycles corresponded to a transition of the tangential force between two rollers decreasing to a stick-slip phenomenon as a steady state. A friction modifier additive (molybdenum dialkyldithiocarbamate) was added to a lubricant to improve rolling contact fatigue (RCF) pitting resistance. This lubricant containing the friction modifier additive exhibited a lifetime that was a factor of 10 greater than the RCF lifetime for the lubricant base oil. Therefore, the tribofilm may affect the tangential force and RCF lifetime. The contact surfaces and subsurface structure, especially in the vicinity of the microcracks, were dynamically reconstructed by severe friction and damage accumulation. Oxygen was detected on the surface of the microcracks.

Work hardening behavior of dual phase copper-iron alloy at low temperature

Yamashita Takayuki, Koga Norimitsu, Kawasaki Takuro, Morooka Satoshi, Tomono Shohei, Umezawa Osamu, … 全著者表示

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING 819 141509-1 - 141509-10 2021年7月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：Elsevier {BV} 共著

Heterogeneous strain accumulation in dwell fatigue for a commercially pure titanium hot rolled sheet: crystal plasticity modelling and experiment

Liangwei Yin, Osamu Umezawa

ISIJ International 61 ( 6 ) 1990 - 2001 2021年6月 [査読有り]

DOI Web of Science CiNii Research

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：一般社団法人日本鉄鋼協会共著

The heterogeneous deformation in a hot-rolled commercially pure titanium grade 1 sheet has been experimentally and numerically investigated under dwell fatigue loading in current paper. The residual strain fields within two regions of interest are probed by digital image correlation (DIC) after interrupted dwell fatigue test. These measurements essentially agree with predictions of a dislocation mechanism-based crystal plasticity model incorporating deformation twinning. The simulated results further indicate that axial strain localization at grain scale mainly derives from prismatic slip activity, followed by pyramidal <a>, basal slip and {1122} compression twinning activities. On this basis, a weighted averaged Schmid factor is proposed to correlate the axial strain accumulation with active plastic deformation modes in individual grains. Besides, the cyclic load shedding within a soft-hard-soft grain pair is captured by crystal plasticity modeling. The stress redistribution from soft to adjacent hard grain implies that the influence of deformation twinning on dwell facet nucleation is limited. The presented study confirms a robust crystal plasticity model and deepens the quantitative analysis of cold dwell fatigue in titanium and its alloys.

Low-temperature tensile properties of Cu-Fe laminated sheets with various number of layers

Koga Norimitsu, Tomono Shohei, Umezawa Osamu

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING 811 141066-1 - 141066-10 2021年4月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：Elsevier {BV} 共著

Crystallographic orientation in raft-like structure developed by tensile deformation in Cu-Fe alloy sheet

N. Koga, S. Tomono, O. Umezawa

IOP Conference Series: Materials Science and Engineering 1121 ( 012006 ) 2021年4月 [査読有り]

DOI

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Investigation of ductile fracture mechanism in multipass drawing of hollow specimen

Shiga Akira, Yamashita Tomohiro, Neishi Yutaka, Umezawa Osamu

MATERIALS TRANSACTIONS 62 ( 4 ) 505 - 511 2021年4月 [査読有り]

DOI Web of Science CiNii Research

記述言語：日本語掲載種別：研究論文（学術雑誌）出版者・発行元：公益社団法人日本金属学会共著

To apply hollow forming technology for car parts, it is necessary to understand the ductile fracture mechanism of hollow forming. In this study, the cold drawing test and the finite element method analysis (FEM) of hollow specimens were carried out. It was clarified that the ductile fracture of hollow specimens in cold drawing was affected by both stress triaxiality and Lode angle parameter. As a result of fracture observation of a hollow specimen, an equiaxed dimple and an elongated dimple were observed. A mixed-mode ductile fracture mechanism (shear deformation of voids and typical void growth and coalescence) for hollow specimens in cold drawing is assumed. This Paper was Originally Published in Japanese in J. JSTP 61 (2020) 33–39.

その他リンク： https://ci.nii.ac.jp/naid/130008002782

Neutron diffraction mapping measurement for Japanese nails in the ancient and present days

Takayuki Yamashita, Stefanus Harjo, Osamu Umezawa, Takuro Kawasaki

JPS Conference Proceedings 33 ( 011063 ) 2021年3月 [査読有り]

DOI

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Stress partitioning behavior of duplex alloys consisting of BCC and FCC phases at low temperature

Takayuki Yamashita, Shohei Tomono, Satoshi Morooka, Stefanus Harjo, Takuro Kawasaki, Tatsuya Nameki … 全著者表示

JPS Conference Proceedings 33 ( 011064 ) 2021年3月 [査読有り]

DOI

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Influence of microstructure constituents on ductile to brittle transition behavior in multi-phase steel sheets

Hiroyuki Kawata, Osamu Umezawa

ISIJ International 61 ( 3 ) 1002 - 1010 2021年3月 [査読有り]

DOI Web of Science CiNii Research

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：一般社団法人日本鉄鋼協会共著

The influence of martensite-austenite constituents on the two-step ductile to brittle transition (DBT) behavior of low carbon steel sheets was evaluated using Charpy impact tests with sub-size specimens. Four kinds of steel sheets containing 0–38% volume fraction of MA and polygonal ferrite in the matrix were chosen. Small volumes of MA (i.e., 2 and 14%) revealed a slightly higher transition temperature between the middle shelf (MS) and lower shelf, TML, compared to sheets with 0% MA. Furthermore, the transition temperature between the upper shelf and MS was not affected. The steel sheet containing 38% MA constituents exhibited a normal one-step DBT curve without MS, and a significantly higher transition temperature than the steel sheets containing 0, 2, and 14% MA. The increase in the austenite volume fraction in MA from 0.6 to 10.2% was not responsible for the DBT behavior, which may depend on the volume fraction of martensite in MA. A model of two-step DBT for multi-phase steel sheets, in which the small volume of MA lowered the fracture stress of the hard structure and elevated TML, was proposed. The TML depended on the intersection between the fracture stress of the hard structure and the yield stress of the soft structure. In the two-step DBT, the cleavage crack propagation was arrested at ferrite grain boundaries through the MS. A large volume of MA (e.g., all the ferrite grains fully covered) may promote one-step DBT in multi-phase steel sheets, owing to cleavage crack propagation.

Influence of layer thickness on tensile deformation and fracture in ferrite + martensite fine multi-layered steel sheets

Norimitsu Koga, Masayuki Suzuki, Osamu Umezawa

Materials Science and Engineering A 806 140599-1 - 140599-9 2021年3月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：Elsevier 共著

Effect of solute carbon on the characteristic hardening of steel at high temperature

Norimitsu Koga, Osamu Umezawa, Masayuki Yamamoto, Takashi Yamamoto, Takayuki Yamashita, Satoshi Mor … 全著者表示

Metallurgical and Materials Transactions A 52 ( 3 ) 897 - 901 2021年3月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：Springer 共著

Equiaxed α microstructure evolution in wrought Ti-10Al-1Zr-1Mo-1Nb alloy during annealing

Shintaro Tanii, Osamu Umezawa, Yoko Yamabe-Mitarai

Journal of Alloys and Compounds 854 157184-1 - 157184-13 2021年2月 [査読有り]

DOI Web of Science

担当区分：責任著者記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：Elsevier 共著

Tensile properties and deformation behavior of ferrite and austenite duplex stainless steel at cryogenic temperatures

Norimitsu Koga, Tatsuya Nameki, Osamu Umezawa, Valentin Tschan, Klaus-Peter Weiss

Materials Science and Engineering A 801 140442-1 - 140442-8 2021年1月 [査読有り]

DOI Web of Science CiNii Research

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：Elsevier 共著

The tensile properties and deformation and fracture behaviors of a commercial ferrite (body-centered cubic) and austenite (face-centered cubic) duplex stainless steel were investigated at cryogenic temperatures, and the mechanism underlying the improvement in the tensile properties of the steel at cryogenic temperatures was discussed. The strength of the steel increased continuously with lowering temperature, and the elongation hardly decreased with a decrease in temperature from 293 K to 77 K. At 40 K, the elongation of the steel decreased drastically, however, it increased significantly at 8 K. The serration of the steel was measured during its tensile test at 8 K. The volume fraction of the deformation induced martensite was high at 77 K and 8 K, while it was low at 40 K. The strain accumulated in the ferrite and austenite phases during the deformation process remained almost constant at all the test temperatures. The ductile fracture occurred 293 K, 200 K, 77 K, and 8 K, while brittle fracture occurred at 40 K. The low volume fraction of the deformation induced martensite and the occurrence of brittle fracture can explain the low elongation of the steel at 40 K. At 8 K, the occurrence of serration may increase the temperature in the deformation region, which led to an increase in the volume fraction of the deformation induced martensite, as well as the suppression of brittle fracture, resulting in high elongation. The occurrence of deformation induced martensitic transformation, simultaneous deformation of ferrite and austenite, ductile fracture contribute to improvement of tensile property of ferrite and austenite duplex stainless steel at cryogenic temperatures.

Microstructure and low temperature tensile properties in Cu–50 mass%Fe alloy

Koga Norimitsu, Zhang Weisi, Tomono Shohei, Umezawa Osamu

MATERIALS TRANSACTIONS 62 ( 1 ) 57 - 61 2021年1月 [査読有り]

DOI CiNii Research

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：公益社団法人日本金属学会共著

The temperature dependence of the mechanical properties of metals is closely related to its crystal structure. In bcc metals, the strength of the material increases with decreasing temperature, and the ductility decreases drastically at low temperatures. The mechanical properties of fcc metals hardly depend on temperature, and thus fcc metals exhibit large elongations even at low temperatures. In this study, the microstructure and low-temperature tensile properties of Cu–50 mass%Fe alloy consisting of fcc (Cu) and bcc (Fe) dual-phase structures were investigated. The Cu and Fe layers were aligned along the rolling direction. The deformation structures remained after annealing at 1023 K for 1.8 ks, while recrystallized ultra-fine grains were formed after annealing at 1123 K for 1.8 ks. At both annealing temperatures, Cu and Fe precipitated in the Fe and Cu layers, respectively. The elongation obtained when the alloy was annealed at 1123 K for 1.8 ks was higher than that at 1023 K for 1.8 ks. The recovery of strain and the formation of ultra-fine grain during annealing at 1123 K were largely responsible for the higher elongation. The tensile strength at 77 K was higher than that at 293 K for both annealing temperatures. Nevertheless, the elongation at 77 K was approximately equal to that at 293 K. Therefore, the fcc and bcc dual-phase structures has an excellent temperature dependence of mechanical properties: high strength in bcc structure and high elongation in fcc structure at low temperatures. A dimple fracture surface appeared at 77 K, indicating that ductile fracture occurred in both phases. Therefore, the Fe phase exhibited significant ductility even at 77 K. The excellent low-temperature tensile properties of the Cu–Fe dual-phase alloy may be due to strengthening by the Fe phase and suppressing of brittle fracture in the Fe phase by the ductile Cu phase. This Paper was Originally Published in Japanese in J. Japan Inst. Copper 59 (2020) 289–293. All captions are slightly changed.

その他リンク： https://ci.nii.ac.jp/naid/130007947225

Effect of the Laves phase and carbide on the creep strength of Fe–C–15Cr–W alloys

Yoshiaki Toda, Yuki Nakamura, Naomichi Harada, Akihiro Kaseya, Nina Kobata, Yoko Yamabe-Mitarai, Os … 全著者表示

Materials Science and Engineering A 797 140104-1 - 140104-9 2020年10月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：Elsevier 共著

Equiaxed α microstructure evolution in wrought Ti-10Al-1Zr-1Mo-1Nb alloy during annealing

Tanii Shintaro, Umezawa Osamu, Yamabe-Mitarai Yoko

Journal of alloys and compounds 854 157184 2020年10月 [査読有り]

CiNii Research

担当区分：責任著者記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：Elsevier 共著

Evolution of α microstructure on the thermomechanical treated Ti-10Al-1Zr-1Mo-1Nb alloy during annealing was studied. The solution-treated materials were groove-rolled or uniaxially compressed in the α+β region and annealed at 1173 K. The flow softening behavior and crystal rotation in α platelets revealed an evolution of deformation texture. The volume fraction of equiaxed α grains was increased during annealing. Especially in the material compressed at a strain rate of 1 s−1, the equiaxed α grains developed within a shorter annealing duration than 1.8 ks. The deformation with higher strain rates promoted the division and fragmentation of α platelets during annealing. Transmission electron microscopy and X-ray diffraction analyses were employed to characterize dislocation components and structure, where the installed screw dislocations provided a fine substructure and high energy α/α boundaries in α platelets. The triple junction consisting of α/β boundaries and α/α boundaries may provide a site for thermal grooving, which induces the division and fragmentation of α platelets. Therefore, deformation at a higher strain rate is necessary in α+β processing to develop a fine equiaxed α microstructure for the Ti-10Al-1Zr-1Mo-1Nb alloy during annealing.

Microstructural evolution in Ti-10Al-1Zr-1Mo-1Nb alloy under thermomechanical treatment in the β-region

Shintaro Tanii, Osamu Umezawa, Yoko Yamabe-Mitarai

Materials Science and Engineering A 796 140149-1 - 140149-10 2020年10月 [査読有り]

DOI Web of Science

担当区分：責任著者記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：Elsevier 共著

Strain distribution and deformation-induced martensitic transformation in tension for a TRIP steel plate

Koga Norimitsu, Yamashita Takayuki, Umezawa Osamu

ISIJ International 60 ( 9 ) 2083 - 2089 2020年9月 [査読有り]

DOI Web of Science CiNii Research

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：一般社団法人日本鉄鋼協会共著

Digital image correlation was applied to analyze the strain distribution and deformation-induced martensitic transformation of retained austenite in a low alloy transformation-induced plasticity (TRIP) steel plate under tension. The distribution of strain instilled by tensile deformation was inhomogeneous at a microscopic scale. Strain generated by deformation-induced martensitic transformation was successfully visualized and it led to a homogeneous strain distribution. The retained austenite in the high strain region transformed to martensite preferentially, which demonstrates that inhomogeneous strain distribution affects the stability of retained austenite. The high resolution strain distribution exhibited that a certain amount of strain instilled into retained austenites and there are a lot of strain concentration sites at ferrite/austenite interfacial boundaries in high strain region. Therefore, the stress concentration at the ferrite/retained austenite interfacial boundary occurs due to the difference of strain between the ferrite matrix and retained austenite. These strain accumulation in a retained austenite and/or stress concentration at ferrite/retained austenite interfacial boundary may induce martensitic transformation in high strain regions.

その他リンク： https://ci.nii.ac.jp/naid/130007833003

Microstructural evolution in Ti–10Al–1Zr–1Mo–1Nb alloy under thermomechanical treatment in β-region

Tanii Shintaro, Umezawa Osamu, Yamabe-Mitarai Yoko

Materials Science and Engineering: A 796 2020年9月 [査読有り]

CiNii Research

担当区分：責任著者記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：Elsevier 共著

The influence of temperature and strain rate on microstructural evolution in near α-type Ti–10Al–1Zr–1Mo–1Nb alloy was studied under uniaxial compression in the β single-phase-region. Hot compression tests were conducted for up to 75% reduction at temperatures between 1273 K and 1333 K and strain rates between 0.01 s^−1 and 5 s^−1. The steady-state of the flow behavior revealed that dynamic recovery in the β single-phase was dominant in the microstructural evolution process, and few dynamically recrystallized grains were detected, except in the vicinity of the pre-existing β grain boundaries. Two types of configurations such as lamellar α_L and acicular α_AC microstructures were developed, which were consistent with the compressive deformation mechanism in the β-region. The α_L microstructure consisted of α platelets that were developed via growth of a specific variant, whereas the α_AC microstructure consisted of individual α platelets with a different variant in the prior-β matrix. The stress exponent and activation energy were evaluated to determine the deformation mechanism. The heterogeneous nucleation of individual α platelets in the cellular structure (sub-grains) without a specific orientation in the β matrix resulted in the αAC microstructure. In contrast, the substructure as uniformly distributed dislocations in prior-β grains under the viscous motion of dislocations promoted a single variant selection to form αL platelets in the transformation. When the viscous drag dislocation motion in the β-region is dominant, a large crystal rotation is detected in the acicular (side plate) α_SP platelets in the vicinity of the prior-β grain boundary.

Tensile deformation of texture-controlled titanium with high oxygen content at room temperature

Motoaki Morita, Shogo Suzuki, Yaku Kato, Weibo Li, Osamu Umezawa

Materials Science and Engineering A 793 139660-1 - 139660-14 2020年8月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）共著

Cu-50mass％Fe二相合金の組織と低温引張特性

古賀紀光, 張偉思, 友野翔平, 梅澤修

銅と銅合金 59 ( 1 ) 289 - 293 2020年8月 [査読有り]

DOI

記述言語：日本語掲載種別：研究論文（学術雑誌）出版者・発行元：日本銅学会共著

The temperature dependence on mechanical properties in a metal material relates to its crystal structure. In a bcc metal, the strength increases with lowering temperature though the ductility decreases drastically at a low temperature. While mechanical properties in an fcc metal hardly depend on temperature, and thus the fcc metal exhibits high elongation even at low temperatures. In this study, the microstructure and low temperature tensile properties in Cu–50mass％Fe alloy consisting of fcc （Cu） and bcc （Fe） dual phase structure were investigated. Cu and Fe layers were aligned along the rolling direction. The microstructure after annealing at 1023 K for 1.8 ks maintained a deformation structure, while it after annealing at 1123 K for 1.8 ks was the recrystallized ultra–fine grain. In both annealing temperature, Cu and Fe precipitated in Fe and Cu layers, respectively. The elongation in the specimen annealing at 1123 K for 1.8 ks was higher than that of the specimen annealing at 1023 K for 1.8 ks. The recovery of strain and ultra–fine grains should improve the elongation in the specimen annealing at 1123 K. The tensile strength at 77 K was higher than that at 293 K in both specimens annealing at 1023 K and 1123 K. Nevertheless, the elongation at 77 K was nearly equivalent to that at 293 K. Therefore, the fcc and bcc dual phase structure has a superior temperature dependence on mechanical properties： high strength in bcc structure and high elongation in fcc structure at low temperature. A dimple fracture surface appeared at 77 K, meaning that the ductile fracture occurs in both phases. Hence, the Fe phase has enough ductility even at 77 K. The superior low temperature tensile properties may be due to strengthening by the Fe phase and suppressing brittle fracture of the Fe phase by the ductile Cu phase.

その他リンク： https://ci.nii.ac.jp/naid/130007940921

Role of retained austenite in low alloy steel at low temperature monitored by neutron diffraction

Yamashita Takayuki, Morooka Satoshi, Harjo Stefanus, Kawasaki Takuro, Koga Norimitsu, Umezawa Osamu

SCRIPTA MATERIALIA 177 6 - 10 2020年3月 [査読有り]

DOI Web of Science CiNii Research

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：Elsevier Ltd 共著

In-situ neutron diffraction measurements during tensile tests at low temperatures of a low alloy steel containing retained austenite (γ) have been performed. Evolutions of phase fractions and phase stresses were analyzed and discussed with the progress of deformation. The role of γ in the steel during deformation at low temperatures was observed not to directly in the contribution to the strengths but in the improvement of the elongation by transformation of γ to martensite -and in the increasing of the work-hardening rate by an increase in the phase fraction of martensite and the work hardening of martensite.

<111> 優先配向したアルミニウム矩形引抜線材の繰返し曲げ変形

池谷隼人，梅澤修，福富洋志

軽金属 70 ( 2 ) 51 - 55 2020年2月 [査読有り]

DOI

記述言語：日本語掲載種別：研究論文（学術雑誌）出版者・発行元：一般社団法人軽金属学会共著

中空材の引抜き加工における延性破壊メカニズム検討

志賀聡, 山下朋広, 根石豊, 梅澤修

塑性と加工 61 ( 709 ) 33 - 39 2020年2月 [査読有り]

DOI CiNii Research

記述言語：日本語掲載種別：研究論文（学術雑誌）出版者・発行元：一般社団法人日本塑性加工学会共著

その他リンク： https://ci.nii.ac.jp/naid/130007801667

Effects of surface compound layer on bending fatigue strength of nitrided chromium molybdenum steel

Tsuyoshi Kubota, Osamu Umezawa

SAE International Journal of Advances and Current Practices in Mobility 2 ( 2 ) 979 - 984 2020年1月 [査読有り]

記述言語：英語掲載種別：研究論文（学術雑誌）共著

Modeling of surface crack defects developed on shear edge in high-strength automotive steel sheets

Goto Sota, Yamazaki Kazuhiko, Doan Thi-Huyen, Funakawa Yoshimasa, Umezawa Osamu

ISIJ International 60 ( 1 ) 143 - 152 2020年1月 [査読有り]

DOI Web of Science CiNii Research

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：一般社団法人日本鉄鋼協会共著

Surface crack defects developed on the shear edge cause a problem in shearing of high-strength steels. The surface crack formation mechanism was clarified by microstructural examinations and numerical simulation. Two types of 780 MPa grade hot-rolled steel sheets with a thickness of 2.6 mm were chosen for the evaluations because the materials show different surface crack susceptibilities. Cleavage fracture was responsible for the surface cracks, and micro-ductile cracks with a length of 30 µm to 40 µm were detected in the interrupted punching samples. A numerical simulation demonstrated that a tensile stress was developed in the direction of the micro-ductile cracks opening during punching process. The critical length of the micro-ductile crack for cleavage fracture as a crack initiation site was given by linear fracture mechanics; for example, the critical length is 23 µm or longer under the applied tensile stress of 910 MPa. The tensile stress causing cleavage fracture decreased by reducing the tool clearances, and it was shown experimentally that surface crack defects can be prevented by controlling the clearance appropriately.

その他リンク： https://ci.nii.ac.jp/naid/130007786265

種々の初期集合組織を有するAZ31BおよびAZ80マグネシウム合金の高温平面ひずみ圧縮変形下での組織と集合組織の形成機構

福富洋志, 朴亨均, 金卷煦, 岡安和人, 長谷川誠, 梅澤修

日本金属学会誌 83 ( 8 ) 264 - 272 2019年8月 [査読有り]

DOI Web of Science

記述言語：日本語掲載種別：研究論文（学術雑誌）出版者・発行元：公益社団法人日本金属学会共著

The effects of pre-existent textures on the evolution behaviors of microstructure and texture at high-temperature plane strain compression deformation of AZ31B magnesium alloy have been studied. Deformation is conducted at 723 K with a strain rate of 5.0 × 10−2 s−1, up to −1.3 in true strain. When non-basal slip systems are the primary slip systems, {1120}<1010> texture develops. In this case, repeated change in microstructure and texture which was found in the previous work appeared with increasing strain. Namely, replacement of {1120}<1010> texture with {1010}<1120> texture and the reverse phenomenon occurs. While the {1120}<1010> oriented grains are small and with wavy shaped grain boundaries, the {1010}<1120> oriented grains are large and with rather straight grain boundaries. The mechanism of repeated change in microstructure and texture is discussed on the basis of preferential dynamic grain growth mechanism proposed by the authors.

その他リンク： https://ci.nii.ac.jp/naid/130007683520

Effect of pearlite volume fraction on two-step ductile to brittle transition in ferrite + pearlite structure steel sheets

Hiroyuki Kawata, Osamu Umezawa

ISIJ International 59 ( 7 ) 1344 - 1353 2019年7月 [査読有り]

DOI

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：一般社団法人日本鉄鋼協会共著

Multi structural steels exhibit high strength and good formability; however, their performance depends on the volume fraction of the secondary phase. In our previous study, ferrite + pearlite structural steel sheet showed the characteristic two-step ductile-to-brittle transition (DBT) with decreasing temperature, and the absorbed energy curve exhibited a distinct middle shelf. In this study, we evaluated the effect of pearlite volume fraction (VP) on the DBT behavior by the Charpy impact test with sub-size specimens. For specimens without pearlite, the absorbed energy directly dropped from the upper shelf to the lower shelf with decreasing temperature. For samples with 2–3% pearlite, the absorbed energy corresponding to the transition temperature range was dispersed between the two shelves, and the transition behavior seemed to be the typical DBT behavior. When VP was increased to 21%, the absorbed energy just above the transition-finish temperature became stable at a middle level between the two shelves; thus, the existence of a distinct middle shelf was confirmed. Although the transition-start temperature increased with increasing VP, VP did not affect the transition-finish temperature and the absorbed energy at the middle shelf. These results were analyzed with a simple model based on the Yoffee diagram.

その他リンク： https://ci.nii.ac.jp/naid/130007679258

Crystal orientation analysis on stress corrosion cracking facets in austenitic stainless steels

Ryo Wakinaga, Norimitsu Koga, Osamu Umezawa, Motoaki Morita, Shinichi Motoda, Tadashi Shinohara

Key Engineering Materials 810 64 - 69 2019年7月 [査読有り] [招待有り]

DOI

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

アルミニウム線材の繰返し曲げ変形における結晶格子回転と疲労亀裂形成

池谷隼人, 梅澤修, 福富洋志

軽金属 69 ( 6 ) 302 - 308 2019年6月 [査読有り]

DOI

記述言語：日本語掲載種別：研究論文（学術雑誌）出版者・発行元：一般社団法人軽金属学会共著

The relationship between the grain boundary steps on the specimen surface developed by cyclic bending and fatigue crack generation on the grain boundaries inclined at about 45 degree to the principal stress axis has been discussed for 4N-aluminum wire. The crystal lattice rotation near the grain boundary induced by slip bands in a grain resulted in a strain incompatibility with the neighboring grain. Due to the shear deformation along the grain boundary, the individual grain boundary steps coalesce and form a grain boundary microcrack, resulting in the fatigue crack generation and propagation. The strain incompatibility is developed at the grain boundary between the grain accompanied with crystal rotation over 10 degrees in the vicinity of the boundary and the grain with almost no crystal rotation. Based on the approximation that only the primary slip system is operative, the step height due to the crystal slip deformation is estimated from the lattice rotation near the grain boundary.

その他リンク： https://ci.nii.ac.jp/naid/130007684576

IMPROVEMENT IN CREEP AND STEAM OXIDATION RESISTANCE OF PRECIPITATION STRENGTHENED FERRITIC STEELS

Toda Yoshiaki, Yoko Yamabe-Mitarai, Akihiko Kaseya, Umezawa Osamu

JOINT EPRI - 123HIMAT INTERNATIONAL CONFERENCE ON ADVANCES IN HIGH-TEMPERATURE MATERIALS, 2019 96 - 103 2019年

Web of Science

記述言語：日本語掲載種別：研究論文（国際会議プロシーディングス）共著

A Subsurface fatigue crack generation model in near alpha titanium at low temperature

Osamu Umezawa, Weibo Li

Materials Science Forum 941 1336 - 1341 2018年12月 [査読有り] [招待有り]

DOI

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Middle shelf during ductile to brittle transition on ferrite + pearlite structural steel sheet

Hiroyuki Kawata, Osamu Umezawa

Materials Science Forum 941 453 - 457 2018年12月 [査読有り]

DOI

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Visualization of strain distribution in tensile test of ferrite + martensite multilayered steel sheet by digital image correlation method

Norimitsu Koga,Masayuki Suzuki,Osamu Umezawa

Procedia Manufacturing 15 1656 - 1662 2018年9月 [査読有り]

DOI

記述言語：英語掲載種別：研究論文（学術雑誌）共著

Detection of surface roughness evolution of carbon steel subjected to outdoor exposure test and constant humidity corrosion tests

Dara To, Osamu Umezawa, Tadashi Shinohara

Materials Transactions 59 ( 8 ) 1239 - 1243 2018年8月 [査読有り]

DOI

記述言語：英語掲載種別：研究論文（学術雑誌）共著

Fractographical analyses of crack initiation site in high-cycle fatigue for Ti-Fe-O alloy at low temperature

Osamu Umezawa, Takayuki Yuasa, Weibo Li

ISIJ International 58 ( 7 ) 1332 - 1340 2018年7月 [査読有り]

DOI

記述言語：英語掲載種別：研究論文（学術雑誌）共著

Influence of deformability of retained austenite on martensitic transformation in tension for low alloy steel at low temperatures

Takayuki Yamashita, Norimitsu Koga, Osamu Umezawa

ISIJ International 58 ( 6 ) 1155 - 1161 2018年6月 [査読有り]

DOI

記述言語：英語掲載種別：研究論文（学術雑誌）共著

微細組織から見たアルミニウム線材の繰返し曲げ変形と破壊挙動

池谷隼人，梅澤修，福富洋志

軽金属 68 ( 5 ) 243 - 249 2018年5月 [査読有り]

記述言語：日本語掲載種別：研究論文（学術雑誌）共著

Martensitic transformation of retained austenite in ferrite matrix for low alloy steel

Takayuki Yamashita, Norimitsu Koga, Osamu Umezawa

Materials Tranactions 59 ( 5 ) 712 - 716 2018年5月 [査読有り]

DOI

記述言語：英語掲載種別：研究論文（学術雑誌）共著

Analysis of subsurface fatigue crack generation in Ti-Fe-O alloy at low temperature

Weibo Li, Osamu Umezawa, Norimitsu Koga

ISIJ International 58 ( 2 ) 359 - 363 2018年2月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：IRON STEEL INST JAPAN KEIDANREN KAIKAN 共著

Crystallographic characterization of the middle shelf in a two-step ductile to brittle transition for a ferrite + pearlite structure steel sheet

Hiroyuki Kawata, Osamu Umezawa

Materials Science and Engineering A 716 252 - 259 2018年2月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：ELSEVIER 共著

Temperature dependence on tensile properties of Cu-40mass%Fe dual phase alloy

Norimitsu Koga, Weisi Zhang, Osamu Umezawa, Valentin Tschan, Jan Sas, Klaus-Peter Weiss

IOP Conference Series: Materials Science and Engineering 279 012004 2018年1月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）出版者・発行元：IOP PUBLISHING LTD 共著

Two step ductile to brittle transition behavior on ferrite + pearlite structure steel sheet

Hiroyuki Kawata, Osamu Umezawa

ISIJ International 57 ( 7 ) 1282 - 1288 2017年7月 [査読有り]

DOI Web of Science J-GLOBAL

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：Iron and Steel Institute of Japan 共著

その他リンク： https://www.jstage.jst.go.jp/article/isijinternational/57/7/57_ISIJINT-2017-026/_article

Effects of slip ratio on damage and microcracks in carburized SCM420 steel under rolling contact fatigue

Junichi Sanekata, Norimitsu Koga, Osamu Umezawa

Key Engineering Materials 741 94 - 98 2017年6月 [査読有り] [招待有り]

DOI

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Mechanical stability and deformation-induced transformation of retained austenite in TRIP steels at low temperature

Takayuki Yamashita, Norimitsu Koga, Osamu Umezawa

Key Engineering Materials 741 36 - 41 2017年6月 [査読有り] [招待有り]

DOI

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Effect of Si content on fatigue fracture behavior of hot-rolled high-silicon steels

Osamu Umezawa, Jyunichi Kanda and Takao Yamazaki

Journal of Physics 843 ( 1 ) 012046 2017年5月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）出版者・発行元：IOP PUBLISHING LTD 共著

A study on the initial atmospheric corrosion behaviors of carbon steel exposed to urban and marine atmosphere in Cambodia

Dara To, Tadashi Shinohara, Osamu Umezawa

材料と環境 66 ( 4 ) 131 - 135 2017年4月 [査読有り]

DOI

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：日本腐食防食学会共著

ガス窒化処理したSCM435鋼の回転曲げ疲労強度に及ぼす表面化合物相の影響

平岡泰，石田暁丈，梅澤修

熱処理 57 ( 2 ) 64 - 72 2017年4月 [査読有り]

DOI J-GLOBAL

記述言語：日本語掲載種別：研究論文（学術雑誌）出版者・発行元：一般社団法人日本熱処理技術協会共著

その他リンク： https://www.jstage.jst.go.jp/article/netsushori/57/2/57_64/_article/-char/ja/

Development of artificial rainfall equipment for studying the effect of rain on the corrosion behaviors

Dara To, Tadashi Shinohara, Osamu Umezawa

材料と環境 66 ( 2 ) 58 - 61 2017年2月 [査読有り]

DOI J-GLOBAL

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：日本腐食防食学会共著

その他リンク： https://www.jstage.jst.go.jp/article/jcorr/66/2/66_58/_article

Effects of cross-rolling on deformation texture evolution in unalloyed titanium

Osamu Umezawa, Norimitsu Koga

Materials Science Forum 879 2014 - 2019 2017年2月 [査読有り]

DOI

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：Trans Tech Publications, 共著

工業用純チタンの多パス冷間圧延における圧延集合組織形成について、付加的せん断ひずみの影響を評価した。タンデムおよびリバース圧延とクロス角度（5および10度）により極密度が変することをX線回折にて示し、すべり帯等の変形組織形成についてEBSD法を用いて明らかにした。

炭酸カルシウム結晶多形の転移と結晶成長に及ぼす材料表面溶出イオンの影響

橋本凌平，盛田元彰，梅澤修，元田慎一

日本金属学会誌 81 ( 2 ) 89 - 96 2017年2月 [査読有り]

DOI J-GLOBAL

記述言語：日本語掲載種別：研究論文（学術雑誌）出版者・発行元：日本金属学会共著

その他リンク： https://www.jstage.jst.go.jp/article/jinstmet/81/2/81_J2016045/_article/-char/ja/

Experimental investigation on the corrosivity of atmosphere through the atmospheric corrosion monitoring (ACM) sensors

Dara To, Tadashi Shinohara, Osamu Umezawa

ECS Transactions 75 ( 29 ) 1 - 10 2017年1月 [査読有り]

DOI

記述言語：英語掲載種別：研究論文（学術雑誌）共著

A model of scale formation on inner carbon steel pipe walls for transporting hot spring water

M. Morita, O. Umezawa

Materials Transactions 57 ( 9 ) 1652 - 1659 2016年9月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：JAPAN INST METALS 共著

炭素鋼管に温泉水を流動させ，付着したスケールを分析し，付着スケール基本構造とその形成過程について概念モデルを提示した。
（原著24の英訳）

Effects of anion on the corrosion behaviors of carbon steel under artificial rainfall

Dara To, Tadashi Shinohara and Osamu Umezawa

The Ninth Pacific Rim International Conference on Advanced Materials and Processing 276 - 281 2016年8月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）出版者・発行元：The Japan Institute of Metals and Materials 共著

人工雨を用いて、低炭素鋼材の大気腐食を模擬するとともに、開発したガルバニック対により腐食速度の評価を行った。

Effects of anion on the corrosion behaviors of carbon steel under artificial experiment

Dara To, Tadashi Shinohara, Osamu Umezawa

International Journal of Research in Engineering and Technology 5 ( 8 ) 382 - 387 2016年8月 [査読有り]

記述言語：英語掲載種別：研究論文（学術雑誌）共著

人工雨を用いて、低炭素鋼材の大気腐食を模擬するとともに、開発したACMセンサー（ガルバニック対）により腐食速度の評価を行った。ACMセンサーは大気腐食の予測に有効であり、腐食速度が大気中の腐食物質の成分に依存するとともに、その予測が可能であることを示した。

Effects of α-grain structure on cyclic deformation structure of Ti-Fe-O alloy at low temperature

Weibo Li, Osamu Umezawa

Proceedings of the 13th World Conference on Titanium 843 - 847 2016年7月 [査読有り]

DOI

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）出版者・発行元：John Wiley & Sons, Inc. 共著

集合組織の異なるTi-Fe-O合金材を用い、低温高サイクル疲労で形成する飽和転位組織が異なること、そして、粒界部に形成するひずみ不整合がき裂発生要因であることを示した。

Evaluation of fatigue crack growth in α-titanium alloys

O. Umezawa, M. Hamada, T. Tatsumi

Procedia Materials Science 12 48 - 53 2016年5月 [査読有り] [招待有り]

DOI

記述言語：英語掲載種別：研究論文（学術雑誌）共著

微視組織形態の異なる工業用純TiおよびTi-Fe-O合金材を用い、それらの低温高サイクル疲労により形成した内部き裂発生点の形態と位置を評価し、線形力学解析シミュレーションに適用してき裂伝播挙動のモデル化を行った。微小き裂成長を抑制する微視組織制御の重要性を導いた。

地熱熱水輸送用炭素鋼管に付着するスケール形成過程のモデル化

盛田元彰，梅澤修

日本金属学会誌 80 ( 5 ) 309 - 316 2016年5月 [査読有り]

DOI J-GLOBAL

記述言語：日本語掲載種別：研究論文（学術雑誌）出版者・発行元：公益社団法人日本金属学会共著

炭素鋼管に温泉水を流動させ，付着したスケールを分析し，付着スケール基本構造とその形成過程について概念モデルを提示した。

その他リンク： https://www.jstage.jst.go.jp/article/jinstmet/80/5/80_J2015051/_article/-char/ja/

ガス窒化処理したクロム含有低合金鋼の拡散層硬さに及ぼす窒化温度と合金成分の影響

平岡泰，渡邉陽一，梅澤修

日本金属学会誌 80 ( 4 ) 253 - 258 2016年4月 [査読有り]

DOI J-GLOBAL

記述言語：日本語掲載種別：研究論文（学術雑誌）出版者・発行元：公益社団法人日本金属学会共著

ガス窒化処理したCr含有低合金鋼の拡散層硬さ分布および拡散層中の窒素濃度を評価し、拡散層硬さと窒素濃度の関係に及ぼす窒化処理温度と鋼種の影響を明らかにした。

その他リンク： https://www.jstage.jst.go.jp/article/jinstmet/80/4/80_J2015066/_article/-char/ja/

ガス窒化処理したクロム含有低合金鋼における拡散層硬さ分布予測の実用モデル

平岡泰，渡邉陽一，梅澤修

日本金属学会誌 80 ( 4 ) 259 - 267 2016年4月 [査読有り]

DOI J-GLOBAL

記述言語：日本語掲載種別：研究論文（学術雑誌）出版者・発行元：公益社団法人日本金属学会共著

ガス窒化処理したCr含有低合金鋼における固溶窒素の拡散場を解き、同時にCrNやAlNの体積のみ求める核生成・成長型の計算モデル構築を行い、拡散層硬さ分布の実測値を用いた計算モデルの評価とモデルの精度について検証した。

その他リンク： https://www.jstage.jst.go.jp/article/jinstmet/80/4/80_J2015067/_article/-char/ja/

Tensile properties and conductivities of a precipitation hardened and cold-rolled Cu-0.3Cr-0.1Zr alloy at cryogenic temperature

Osamu Umezawa

IOP Conference Series: Materials Science and Engineering 102 012006 2015年12月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）出版者・発行元：IOP PUBLISHING LTD 単著

Cu-0.3Cr-0.1Zr合金の極低温における引張特性、電気抵抗、熱伝導率、磁化特性について評価し、高強度高伝導性材料として位置づけを示した。

低合金鋼のガス窒化により形成する化合物層中のγ’相およびε相の相安定性に及ぼす炭素量の影響

平岡　泰，渡邉陽一，梅澤　修

熱処理 54 ( 6 ) 313 - 318 2014年12月 [査読有り]

DOI J-GLOBAL

記述言語：日本語掲載種別：研究論文（学術雑誌）出版者・発行元：一般社団法人日本熱処理技術協会共著

Feに添加した0.1 ～ 1.0％Cが、Lehrer 図のγ¬′相および ε相の相安定性に及ぼす影響をCALPHAD法による平衡熱力学計算により検討し、炭素量が異なる鋼においてガス窒化処理による実験検証を行った。

その他リンク： https://www.jstage.jst.go.jp/article/netsushori/54/6/54_313/_article/-char/ja/

New aspects of ecomaterials from viewpoints of consumer and regional community

Osamu Umezawa, Yoshikazu Shinohara, Kohmei Halada

Materials Transactions 55 ( 5 ) 745 - 749 2014年5月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：JAPAN INST METALS 共著

エコマテリアルの新しいコンセプトと特徴づけについて提案した。エコマテリアル概念の提唱から現在、そして今後への段階を示し、高いエコ効率から、消費者や地域社会に適合する方向性を議論した。そして、材料のロバスト設計について、エコマテリアルへの新たな導入を提案した。

Practical model to predict nitrogen-diffusion layer's hardness in gas nitrided chromium-containing steel

Yasushi Hiraoka, Youichi Watanabe, Osamu Umezawa

Proceedings of European Conference on Heat Treatment and 21st IFHTSE Congress 119 - 126 2014年5月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）出版者・発行元：Arbeitsgemeineschaft Warmebehandlung u. Werkstofftechnik 共著

ガス窒化処理したCr含有低合金鋼の拡散層硬さ分布を評価する実用モデルを開発するために、固溶窒素の拡散場、CrNやAlN析出カイネティクス、硬さと析出物体積の線形関係について検討した。

局部加圧によるADC12ダイカストの疲労強度向上

井澤龍介, 梅澤　修, 桑田　浩

鋳造工学 86 ( 4 ) 294 - 300 2014年4月 [査読有り]

DOI

記述言語：日本語掲載種別：研究論文（学術雑誌）出版者・発行元：日本鋳造工学会共著

ADC12アルミニウムダイカストの肉厚部に局所加圧を施し、平面曲げ疲労試験における疲労強度下限値の向上を得た。この主要因は、内部欠陥サイズや数密度の低減であることを示し、欠陥サイズと疲労強度との関係を定量的に評価し、局所加圧による凝固直後の高温加工が基地に与える影響を示した。

Lattice parameters and relative stability of α" phase in binary titanium alloys from first-principles calculations

Chun-Xia Li, Hu-Bin Luo, Qing-Miao Hu, Rui Yang, Fu-Xing Yin, Osamu Umezawa, Levente Vitos

Solid State Communications 159 70 - 75 2013年5月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：ELSEVIER 共著

第1原理計算（EMTO(Exact Muffin -Tin Orbitals)-CPA(Coherent Potential Approximation)法）を用いて、Ti-xM (M=V, Nb, Mo, Ta) 2元系合金における斜方晶α”相の幾何学構造と相安定性（対αおよびβ相）、弾性定数について検証した。α”-αおよびα”-β相変態はエネルギー障壁無しに生じ、α”相の形成は共有結合と金属結合の中間的な状態にある。

微粒子ピーニングによるアルミダイカスト材の疲労強度向上

井澤龍介, 梅澤　修, 中村紀夫，高木眞一

鋳造工学 85 ( 3 ) 155 - 160 2013年3月 [査読有り]

記述言語：日本語掲載種別：研究論文（学術雑誌）共著

ADC12アルミニウムダイカスト部品の表面に微粒子ピーニング処理を施し、約5μmの表面改質皮膜の形成や深さ100μm以上にわたる残留圧縮応力の導入により、両振り疲労試験において約50%の疲労強度向上を得た。また、試料表面のマクロ欠陥を塞ぐ効果を確認し、マクロ欠陥を有するダイカスト部品の局所的な疲労特性強化に有効であることを示した。

Novel processes locally to modify aluminum die cast for improving its fatigue strength

R. Izawa, O. Umezawa

5th Inter. Workshop on New Method of Damage and Failure Analysis of Structural Parts 65 - 70 2012年9月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Subsurface crack generation and flacking under rolling contact fatigue

O. Umezawa, S. Morooka, J. Brumek

th Inter. Workshop on New Method of Damage and Failure Analysis of Structural Parts 421 - 427 2012年9月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

In-situ neutron diffraction study on tensile deformation behavior of steels

S. Morooka, H.Kawata, S.Harjo, O. Umezawa

5th Inter. Workshop on New Method of Damage and Failure Analysis of Structural Parts 369 - 375 2012年9月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Fatigue behavior at punched hole in high strength hot-rolled steels

K. Nakajima, Y. Funakawa, D. Tajiri, O. Umezawa

5th Inter. Workshop on New Method of Damage and Failure Analysis of Structural Parts 87 - 92 2012年9月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Theoretical investigations of interstitial atoms in bcc metals: Local lattice distortion and diffusion barrier

Chun-Xia Li, Hu-Bin Luo, Qing-Miao Hu, Fu-Xing Yin, Osamu Umezawa, Rui Yang

Computational Materials Science 58 67 - 70 2012年6月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：ELSEVIER 共著

A modeling approach to evaluate grain interaction induced by {111}<1-10> planar slips in face centered cubic polycrystalline materials

M. Morita, O. Umezawa

ISIJ International 52 ( 6 ) 1163 - 1171 2012年6月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：IRON STEEL INST 共著

その他リンク： https://www.jstage.jst.go.jp/article/isijinternational/52/6/52_1153/_article

その場中性子回折法によるフェライト－マルテンサイト型複合組織鋼における引張変形挙動の定量的解析

諸岡　聡, 梅澤　修, Stefanus, Harjo, 長谷川浩平，田路勇樹

TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN 98 ( 6 ) 311 - 319 2012年6月 [査読有り]

DOI Web of Science J-GLOBAL

記述言語：日本語掲載種別：研究論文（学術雑誌）出版者・発行元：IRON STEEL INST JAPAN KEIDANREN KAIKAN 共著

その他リンク： https://www.jstage.jst.go.jp/article/tetsutohagane/98/6/98_311/_article/-char/ja/

Analysis of heterogeneous deformation behavior by full constraints model in alpha-titanium alloy

M. Morita, O. Umezawa

Proceedings of the 12th World Conference on Titanium 2 1100 - 1103 2012年6月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

First-principles determinations of geometric structure and phase stability of α" phase in binary Ti-xM (M=V, Nb, Mo, and Ta) alloys

Chun-Xia Li, Qing-Miao Hu, Fu-Xing Yin, Osamu Umezawa, Rui Yang

Proceedings of the 12th World Conference on Titanium 3 2121 - 2125 2012年6月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Quantitative Analysis of Tensile Deformation Behavior by In-Situ Neutron Diffraction for Ferrite-Martensite Type Dual-Phase Steels

Morooka Satoshi, Umezawa Osamu, Harjo Stefanus, Hasegawa Kohei, Toji Yuki

TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN 98 ( 6 ) 311 - 319 2012年6月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：THE IRON AND STEEL INSTITUTE OF JAPAN 共著

その場中性子回折法によるフェライト－マルテンサイト型複合組織鋼における引張変形挙動の定量的解析

その他リンク： https://www.jstage.jst.go.jp/article/tetsutohagane/98/6/98_311/_article/-char/ja/

Fatigue crack growth under mixed mode loading of 18CrMo4 steel

Jan Brumek, Osamu Umezawa, Vratislav Mares

21st International Conference on Metallurgy and Materials (METAL 2012) 521 - 526 2012年5月 [査読有り]

Web of Science

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）出版者・発行元：TANGER LTD 共著

会議: 21st International Conference on Metallurgy and Materials
開催地: Brno, CZECH REPUBLIC
日付: MAY 23-25, 2012

Effects of alloying elements on the Snoek-type relaxation in Ti-Nb-X-O alloys (X=Al, Sn, Cr, and Mn)

H. Lu, C.X. Li, F.X. Yin, Q.F. Fang, O. Umezawa

Materials Science and Engineering A 541 28 - 32 2012年4月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：ELSEVIER 共著

Microstructural softening of eutectic and hyper-eutectic Al-Si-X continuous casts by annealing

J. Oshikiri, O. Umezawa, N. Nakamura

Transactions of the Materials Research Society of Japan 37 ( 1 ) 39 - 43 2012年3月 [査読有り]

DOI

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：The Materials Research Society of Japan 共著

その他リンク： https://www.jstage.jst.go.jp/article/tmrsj/37/1/37_39/_article

Effects of alloying elements on the oxygen Snoek-type relaxation in Ti-Nb alloys

Hui Lu, Chunxia Li, Fuxing Yin, Qianfeng Fang, Osamu Umezawa

Solid State Phenomena 184 75 - 80 2012年1月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：TRANS TECH PUBLICATIONS LTD 共著

Microstructural analysis of type 304 metal sleeve

S. Ohtani, S. Morooka, O. Umezawa

Materials Science Forum 702-703 959 - 962 2011年12月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：TRANS TECH PUBLICATIONS LTD 共著

Effects of Fe addition on the Snoek-type damping behavior of surface-oxidation-treated Ti-Mo alloys

Hui Lu, Chunxia Li, Fuxing Yin, Qianfeng Fang, Osamu Umezawa

Metallurgical and Materials Transactions A 42 ( 8 ) 2242 - 2249 2011年8月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：ASM International 共著

その他リンク： https://link.springer.com/article/10.1007%2Fs11661-011-0616-0

Slip deformation analysis based on full constraints model for α-titanium alloy at low temperature

M. Morita, O. Umezawa

Materials Transactions 52 ( 8 ) 1595 - 1602 2011年8月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：Japan Institute of Metals 共著

その他リンク： https://www.jstage.jst.go.jp/article/matertrans/52/8/52_L-M2011815/_article

Analysis of crystal rotation by Taylor theory

M. Morita, O. Umezawa

Proceedings of the 2011 Annual Conference on Experimental and Applied Mechanics, Optical measurements, Modeling and Metrolog 5 91 - 96 2011年6月

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

In-situ neutron diffraction study on work-hardening behavior in a ferrite-martensite dual phase steel

S. Morooka, N. Sato, M. Ojima, S. Harjo, Y. Adachi, Y. Tomota and O. Umezawa

JSAE Annual Congress Proceedings 19 ( 11 ) 9 - 14 2011年5月

記述言語：英語掲載種別：研究論文（その他学術会議資料等）出版者・発行元：自動車技術会共著

Softening and fatigue fracture of Al-Si-X alloy casts

J. Oshikiri, O. Umezawa and N. Nakamura

JSAE Annual Congress Proceedings 19 ( 11 ) 5 - 8 2011年5月

記述言語：英語掲載種別：研究論文（その他学術会議資料等）出版者・発行元：自動車技術会共著

Snoek-type damping behavior of surface oxidation-treated Ti-Mo alloys

Hui Lu, Chunxia Li, Fuxing Yin, Qianfeng Fang, Osamu Umezawa

Materials Science and Engineering A 528 ( 9 ) 3358–3366 2011年4月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：ELSEVIER 共著

Influence of heterogeneous deformation on microstructural cracking in alpha-titanium alloys

M. Morita, S. Morooka, O. Umezawa

TMS Supplemental Proceedings: Vol. 3: General Paper Selections 427 - 431 2011年2月 [査読有り]

Web of Science

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）出版者・発行元：JOHN WILEY & SONS 共著

Subjects on fatigue crack generation in high strength alloys for long-life design

O. Umezawa,S.Morooka

ENERGY, ENVIRONMENT AND BIOLOGICAL MATERIALS 685 278 - 284 2011年

DOI Web of Science

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）出版者・発行元：TRANS TECH PUBLICATIONS LTD 共著

内部疲労き裂発生とひずみ不整合の関係について

O. Umezawa

4th Inter. Workshop on New Method of Damage and Failure Analysis of Structural Parts 65 - 70 2010年9月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）出版者・発行元：Vysoká škola báňská - Technická univerzita Ostrava 単著

Aluminum material flow in Japan and novel processes utilizing secondary alloys

O. Umezawa, S. Kumai

Proc. 12th International Conference of Aluminum Alloys 214 - 218 2010年9月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Softening and fatigue fracture of Al-Si-X alloys

J. Oshikiri, N. Nakamura, O. Umezawa

Proc. 12th International Conference of Aluminum Alloys 2381 - 2386 2010年9月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

テイラー解析による不均一すべり変形の評価

M. Morita, O. Umezawa

4th Inter. Workshop on New Method of Damage and Failure Analysis of Structural Parts 71 - 75 2010年9月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）出版者・発行元：Vysoká škola báňská - Technická univerzita Ostrava 共著

Modeling of crack generation and growth under rolling contact fatigue in martensite steels

O.Umezawa, T. Nishikawa, T. Tsuchida, K. Hiraoka

Proc. 18th International Symposium on Processing and Fabrication of Advanced Materials (PFAM18) ( 2 ) 555 - 564 2009年12月

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Subsurface fatigue crack generation and strain incompatibility near grain boundaries for a nitrogen-strengthened austenitic steel at cryogenic temperature

梅澤　修

ISIJ International 49 ( 10 ) 1624 - 1629 2009年10月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：日本鉄鋼協会単著

Electron backscatter diffraction analysis on rolling contact fatigue damage around small cracks in fully tempered martensite steel

O.Umezawa, Y. Yamaji, H. Suzuki

J. Jpn. Soc. Heat Treatment 49 565 - 568 2009年9月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Evaluation of subsurface fatigue crack life in forged Ti-6Al-4V alloys at cryogenic temperatures

Hamada, Makiko; Umezawa, Osamu

ISIJ International 49 ( 1 ) 124 - 131 2009年1月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：日本鉄鋼協会共著

その他リンク： https://www.jstage.jst.go.jp/article/isijinternational/49/1/49_1_124/_article

Novel process development with continuous casting and precise forging for Al-Si alloys to produce an engine piston

O.Umezawa, H. Takagi, T. Sekiguchi, T. Yamashita, N. Miyamoto

Ceramic Transactions: Environmental Issues and Waste Management Technologies in the Materials and Nuclear Industries XII 207 189 - 200 2009年 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Framework of material stock accounts -toward assessment of material accumulation in the economic sphere

S. Hashimoto, I. Daigo, S. Murakami, K. Matsubae-Yokoyama, M. Fuse, K. Nakajima, M. Oguchi, H. Tani … 全著者表示

8th Inter. Conf. Ecobalance 2008年12月

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Novel techniques characterizing subsurface fatigue crack generation and crack growth in high strength forged steels

梅澤修、鈴木宏幸、浜田真規子、横田秀夫、木田勝之

Proc. 3rd Inter. Workshop on New Method of Damage and Failure Analysis of Structural Parts 121 - 126 2008年9月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

High-cycle fatigue properties of fine particle peened Fe-3mass%Si steel sheets

梅澤修,、野崎貴行

Proc. 3rd Inter. Workshop on New Method of Damage and Failure Analysis of Structural Parts 105 - 110 2008年9月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Orientation relationship for fine grains formed by diffusion-induced recrystallization in the Ni(Cu) system

Y. Kawanami, M. Kajihara, O. Umezawa

Materials Transactions 49 ( 2 ) 242 - 249 2008年2月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）共著

Effects of thermo-mechanical treatment on the tensile and compressive properties of a glass-balloon-dispersed aluminum alloy composite

Shiga, Akira; Umezawa, Osamu

Materials Transactions 48 ( 12 ) 3088 - 3094 2007年12月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）共著

Proposal of index of cyclic material use in green environmental profiles

Shiga, Akira; Umezawa, Osamu

Materials Transactions 48 ( 12 ) 3050 - 3055 2007年12月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）共著

Al-Si系二次合金の加工熱処理におけるＬＣＡ評価

中本宗文、梅澤　修

創立20周年記念論文集「世界をリードする日本のものづくり鍛造基盤技術のトレンドを追う“アルミニウム鍛造技術”」 2006年10月

記述言語：日本語掲載種別：研究論文（その他学術会議資料等）共著

Mechanical properties of thermomechanical treated hyper-eutectic Al-Si-(Fe,Mn,Cu) materials

O.Umezawa

Materials Transactions 46 ( 12 ) 2616 - 2623 2005年12月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）単著

その他リンク： https://www.jstage.jst.go.jp/article/matertrans/46/12/46_12_2616/_article

Microstructural refinement of hyper-eutectic Al-Si-Fe-Mn cast alloys to produce a recyclable wrought material

M. Nakamoto, Y. Osawa, K. Suzuki, S. Kumai

Materials Transactions 46 ( 12 ) 2609 - 2615 2005年12月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）共著

その他リンク： https://www.jstage.jst.go.jp/article/matertrans/46/12/46_12_2609/_article

放射光を用いた鋳造組織のX線イメージング

梅澤修、原　徹、大村孝仁

鋳造工学 77 ( 11 ) 759 - 763 2005年11月 [査読有り]

DOI J-GLOBAL

記述言語：日本語掲載種別：研究論文（学術雑誌）出版者・発行元：公益社団法人日本鋳造工学会共著

その他リンク： https://www.jstage.jst.go.jp/article/jfes/77/11/77_11_759/_article

Mechanical Properties of Thermomechanical Treated Hyper-eutectic Al-Si-X Materials

Y. Osawa, S. Takamori

Advances in Ecomaterials 2 480 - 484 2005年7月

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Microstructural refinement of hyper-eutectic Al-Si-X casts to produce a heavily deformable material toward recycling-based society

O.Umezawa,S Nakamoto

6th Inter. Conf. Ecobalance 633 - 636 2004年10月

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Development of civic model on materials technology for recycling-based society

O. Umezawa, H. Ohya, T. Yoshioka, S. Kumai and C. Nishimura

Trans. Mater. Res. Soc. Jpn. 29 ( 5 ) 1829 - 1832 2004年8月 [査読有り]

記述言語：英語掲載種別：研究論文（学術雑誌）共著

A state of the art and development in materials process design and technology for sustainable society

O. Umezawa and K. Nagai

Trans. Mater. Res. Soc. Jpn. 29 ( 5 ) 1925 - 1930 2004年8月 [査読有り]

記述言語：英語掲載種別：研究論文（学術雑誌）共著

Analysis on Refinement of Columnar γ Grain by Phosphorus in Continuously Cast 0.1mass% Carbon Steel

N. Yoshida, O. Umezawa and K. Nagai

ISIJ International 44 ( 3 ) 547 - 555 2004年3月 [査読有り]

DOI

記述言語：英語掲載種別：研究論文（学術雑誌）共著

その他リンク： https://www.jstage.jst.go.jp/article/isijinternational1989/44/3/44_3_547/_article

Effects of partial recrystallization on high-cycle fatigue deformation and crack generation of a nitrogen-strengthened 32Mn-7Cr austenitic steel at liquid nitrogen temperature

O.Umezawa

Metall. Mater. Trans. A 35A ( 2 ) 543 - 553 2004年2月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）単著

True stress-true strain relations with very low strain rates at room temperature for an austenitic 25Cr-19Ni steel

N. Tsuchida, E. Baba, O. Umezawa, K. Nagai and Y. Tomota

ISIJ International 44 ( 1 ) 209 - 213 2004年1月 [査読有り]

DOI

記述言語：英語掲載種別：研究論文（学術雑誌）共著

その他リンク： https://www.jstage.jst.go.jp/article/isijinternational1989/44/1/44_1_209/_article

Influence of phosphorus micro-segregation on ferrite structure in cast strips of 0.1 mass%C steel

O. Umezawa, K. Hirata and K. Nagai

Materials Transaction 44 ( 7 ) 1266 - 1270 2003年7月 [査読有り]

DOI

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：日本金属学会共著

その他リンク： https://www.jstage.jst.go.jp/article/matertrans/44/7/44_7_1266/_article

Phosphorus-induced dislocation structure variation in the warm-rolled ultrafine-grained low-carbon steels

F. Yin, T. Hanamura, O. Umezawa and K. Nagai

Mater. Sci. and Eng. A 354 ( 1-2 ) 31 - 39 2003年4月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）共著

High-cycle fatigue fracture of high strength steels with modified microstructures

S. Shimakura and O. Umezawa

FATIGUE 2003: Fatigue & Durability Assessment of Materials, Components & Structures 505 - 512 2003年4月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Influence of phosphorus on solidification structure in continuously cast 0.1 mass% carbon steel

N. Yoshida, O. Umezawa and K. Nagai

ISIJ International 43 ( 3 ) 348 - 357 2003年3月 [査読有り]

DOI

記述言語：英語掲載種別：研究論文（学術雑誌）共著

その他リンク： https://www.jstage.jst.go.jp/article/isijinternational1989/43/3/43_3_348/_article

Three-dimensional distribution, morphology and nucleation site of intergranular ferrite formed in association with inclusions

T. Yokomizo, M. Enomoto, O. Umezawa, G. Spanos and R.O. Rosenberg

Mater. Sci. and Eng. A 344 261 - 267 2003年2月 [査読有り]

記述言語：英語掲載種別：研究論文（学術雑誌）共著

低環境負荷・資源循環型対応の製鉄プロセス

梅澤　修

ふぇらむ 7 ( 7 ) 27 - 36 2002年7月 [査読有り]

J-GLOBAL

記述言語：日本語掲載種別：研究論文（学術雑誌）出版者・発行元：日本鉄鋼協会単著

Microstructure of cast strip in 0.1 mass%C steels containing phosphorus

HIRATA Koichi,UMEZAWA Osamu,NEGAMI Kotobu

Materials Transaction 43 ( 3 ) 305 - 310, 2002年3月 [査読有り]

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：日本金属学会共著

その他リンク： https://www.jstage.jst.go.jp/article/matertrans/43/3/43_3_305/_article

Continuously cast 0.1 wt% C steels with high phosphorus: microstructural design and control

O. Umezawa, N. Yoshida, K. Hirata, T. Higuchi, N. Sakuma and K. Nagai

J. Advanced Science 13 ( 3 ) 175 - 178 2002年3月 [査読有り]

DOI

記述言語：英語掲載種別：研究論文（学術雑誌）共著

その他リンク： https://www.jstage.jst.go.jp/article/jsas1989/13/3/13_3_175/_article

Improvement of strength-and-toughness balance of recycled steel through ultrarefinement of grain size

T. Hanamura, T. Yamashita, O. Umezawa, S. Torizuka and K. Nagai

J. Advanced Science 13 ( 3 ) 179 - 182 2002年3月 [査読有り]

DOI

記述言語：英語掲載種別：研究論文（学術雑誌）共著

その他リンク： https://www.jstage.jst.go.jp/article/jsas1989/13/3/13_3_175/_article

Application of the Kocks-Mecking model to tensile deformation of an austenitic 25Cr-19Ni steel

N. Tsuchida, Y. Tomota, H. Moriya, O. Umezawa and K. Nagai

Acta Materialia 49 ( 15 ) 3029 - 3038 2001年12月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）共著

Cyclic damage of some high strength alloys showing subsurface crack generation in high-cycle fatigue

O.Umezawa

Proc. Second Inter. Sympo. on Environmentally Concious Design and Inverse Manufacturing 426 - 431 2001年12月 [査読有り]

Web of Science

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）単著

Effects of microstructural refinement by repeated thermomechanical treatment on mechanical properties for hyper-eutectic Al-Si-(Fe, Cu) cast materials

O. Umezawa, H. Yokoyama and K. Nagai

Advances in Materials Engineering and Technology, Special Pub. of Inter. J. of Materials and Product Technology, SPM1 2 568 - 573 2001年12月 [査読有り]

Web of Science

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

現代の和釘の機械的性質とはいかなるものか

梅澤　修

ふぇらむ 6 ( 10 ) 805 - 809 2001年10月 [査読有り]

J-GLOBAL

記述言語：日本語掲載種別：研究論文（学術雑誌）出版者・発行元：社団法人日本鉄鋼協会単著

Improvement of strength-and-toughness balance through ultrafinement of grain size

T. Hanamura, T. Yamashita, O. Umezawa, S. Torizuka, K. Nagai

Inter. Sympo. on Ultrafine Grained Steels (ISUGS 2001) 228 - 231 2001年9月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Time dependent flow behavior of pure aluminium and aluminium-magnesium alloy under a constant stress condition

K. Ishikawa, F. Ishikawa, M. Maehara, Y. Kobayashi and O. Umezawa

CREEP 7 407 - 409 2001年6月 [査読有り]

記述言語：英語掲載種別：研究論文（その他学術会議資料等）共著

Fabrication of Ni3Al thin foil by cold rolling

M. Demura, Y. Suga, O. Umezawa, K. Kishida, E.P. George and T. Hirano

Intermetallics 9 ( 2 ) 157 - 167 2001年2月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）共著

Ductile thin foil of Ni3Al

M. Demura, K. Kishida, O. Umezawa, E.P. George and T. Hirano

Mechanical properties of structural films 1413 248 - 261 2001年2月 [査読有り]

Web of Science

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

低炭素鋼の塑性変形されたオーステナイトの粒界から生成するフェライト粒の形、大きさと結晶方位

鳥塚史郎，梅澤　修，津崎兼彰，長井　寿

鉄と鋼 86 ( 12 ) 807 - 814 2000年12月

DOI

記述言語：日本語掲載種別：研究論文（学術雑誌）出版者・発行元：社団法人日本鉄鋼協会共著

Internal crack initiation in high-cycle fatigue of Ti-Fe-O alloy at liquid nitrogen temperature

H. Yokoyama, O. Umezawa, K. Nagai, T. Suzuki and K. Kokubo

Titanium'99 Sci. and Tech. 622 - 629 2000年12月

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Cyclic deformation, dislocation structure and internal fatigue crack generation in Ti-Fe-O alloy at liquid nitrogen temperature

H. Yokoyama, O. Umezawa, K. Nagai, T. Suzuki and K. Kokubo

Metall. Mater. Trans. A 31 ( 11 ) 2793 - 2805 2000年11月 [査読有り]

記述言語：英語掲載種別：研究論文（学術雑誌）共著

Relationship between size, shape and crystallographic orientation of ferrite grains formed at grain boundaries of deformed austenite in a low carbon steel

S. Torizuka, O. Umezawa, K. Tsuzaki and K. Nagai

HSLA Steel `2000 255 - 259 2000年6月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

超音波振動によるAl-Si合金の固液共存域での初晶形態変化

大澤嘉昭，高森　晋，荒金吾郎，梅澤　修，佐藤　彰，大橋　修

鋳造工学 72 ( 3 ) 187 - 192 2000年3月 [査読有り]

DOI

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：公益社団法人日本鋳造工学会共著

その他リンク： https://www.jstage.jst.go.jp/article/jfes/72/3/72_3_187/_article

Description of stress-strain curves based on thermal activation models for a Ti-Fe-O alloy at 77 to 296 K with strain rates from 10-9 to 10-2 sec-1

N. Tsuchida, H. Moriya, Y. Tomota, O. Umezawa and K. Nagai

ISIJ International 40 ( 1 ) 84 - 90 2000年1月

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）共著

Hot extrusion for Al-Si-(Fe, Cu) hyper-eutectic cast alloys

H. Yokoyama, O. Umezawa, K. Nagai and K. Kokubo

4th Inter. Conf. ECOMATERIALS 491 - 494 1999年11月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Influence of silicon crystal size on fatigue property in hyper-eutectic Al-Si alloy

H. Yokoyama, O. Umezawa, K. Nagai and K. Kokubo

6th Jpn. Inter. SAMPE Sympo. 357 - 360 1999年10月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Microstructural refinement of an As-Cast Al-12.6 Wt Pct Si alloy by repeated thermomechanical treatment to produce a heavily deformable material

O. Umezawa and K. Nagai

Metall. Mater. Trans. A 30A ( Aug ) 2221 - 2228 1999年8月 [査読有り]

DOI

記述言語：英語掲載種別：研究論文（学術雑誌）共著

その他リンク： https://link.springer.com/article/10.1007%2Fs11661-999-0034-8

Effects of high magnetic field on recrystallization and coarsening behavior in Fe-Si steels

Y. Xu, H. Ohtsuka, O. Umezawa, K. Anak, S. Miyazaki and H. Wada

4th Inter. Conf. on Recrystallization and Related Phenomena 571 - 576 1999年7月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Electron microscopy study of cyclic deformation in Ti-Fe-O alloy at low temperature

O. Umezawa, H. Yokoyama, K. Nagai, T. Suzuki and K. Kokubo

FATIGUE '99 211 - 216 1999年6月 [査読有り]

Web of Science

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Effect of strain rate and deformation temperature on fine ferrite grain structure formed from heavily deformed austenite

S. Torizuka, O. Umezawa, K. Tsuzaki, K. Nagai, S. Genda and Y. Kogo

Proc. Inter. Conf. on Solid-Solid Trans. `99 (JIMIC-3) 1533 - 1536 1999年5月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Fracture characteristics and deformation behavior of solution-treated Ti-15V-3Cr-3Sn-3Al alloy

H. Moriya, K. Nagai and O. Umezawa

Int. J. of Materials and Product Technology 14 ( 2-4 ) 229 - 243 1999年4月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（その他学術会議資料等）共著

Fabrication of large-grained binary stoichiometric Ni3Al

T. Hirano, M. Demura, E.P. George and O. Umezawa

Scripta Materialia 40 ( 1 ) 63 - 69 1999年1月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）共著

Effects of test temperature on internal fatigue crack generation associated with nonmetallic particles in austenitic steels

O. Umezawa and K. Nagai

Metall. Mater. Trans. A 29 ( 12 ) 3017 - 3028 1998年12月 [査読有り]

DOI

記述言語：英語掲載種別：研究論文（学術雑誌）共著

その他リンク： https://link.springer.com/article/10.1007%2Fs11661-998-0209-8

Recrystallization in binary stoichiometric Ni3Al

T. Hirano, M. Demura, E.P. George and O. Umezawa

Grain Growth in Polycrystalline Materials Ⅲ 683 - 688 1998年12月 [査読有り]

Web of Science

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Influence of low temperature working on microstructure and mechanical properties of Al-7Si-(Fe) alloys

C.-Y. Lim, O. Umezawa and K. Nagai

Metals and Materials 4 ( 5 ) 1027 - 1031 1998年10月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）共著

Refinement of ferrite-pearlite structures through transformation from heavily deformed austenite in a low carbon Si-Mn steel

S. Torizuka, O. Umezawa, K. Tsuzaki and K. Nagai

Materials Science Forum 284-2 225 - 230 1998年8月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）共著

Deformation structure and subsurface fatigue crack generation in austenitic steels at low temperature

O. Umezawa and K. Nagai

Metall. Mater. Trans. A 29A ( 3 ) 809 - 822 1998年3月 [査読有り]

DOI

記述言語：英語掲載種別：研究論文（学術雑誌）共著

その他リンク： https://link.springer.com/article/10.1007%2Fs11661-998-0272-1

Distribution of internal crack initiation sites in high-cycle fatigue for titanium alloys

H. Yokoyama, O. Umezawa, K. Nagai and T. Suzuki

ISIJ International 37 ( 12 ) 1237 - 1244 1997年12月 [査読有り]

DOI

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：日本鉄鋼協会共著

その他リンク： https://www.jstage.jst.go.jp/article/isijinternational1989/37/12/37_12_1237/_article

Effects of microstructure on the subsurface crack initiation of Ti-6Al-4V alloys

O. Umezawa, K. Nagai, H. Yokoyama and T. Suzuki

High Cycle Fatigue of Structural Materials 287 - 298 1997年12月 [査読有り]

Web of Science

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Metastable alloy phase formation from undercooled steel and Ti-Al melts

S. Tsukamoto and O. Umezawa

Materials Science and Engineering A 223 99 - 113 1997年10月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）共著

Microstructural design and processing of plasticized hyper-eutectic Al-Si-Fe alloys

O. Umezawa and K. Nagai

Proc. 3rd Inter. Conf. ECOMATERIALS 59 - 62 1997年10月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Microstructural design and processing of hyper-eutectic Al-Si alloy and its deformation behavior

O. Umezawa and K. Nagai

Proc. 3rd Inter. Conf. ECOMATERIALS 91 - 94 1997年10月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Microstructural control of recyclable Al-Si-Fe alloys by low temperature working process

C.-Y. Lim, O. Umezawa and K. Nagai

Proc. 3rd Inter. Conf. ECOMATERIALS 99 - 102 1997年10月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Fatigue crack initiation site in titanium alloys at cryogenic temperatures

K. Nagai, T. Yuri and O. Umezawa

Titanium'95 Sci. and Tech. Ⅱ 1139 - 1146 1996年12月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Recyclable design and heavily plasticization for an eutectic Al-Si cast alloy

O. Umezawa and K. Nagai

Trans. of the Mater. Res. Soc. of Jpn 20 190 - 193 1996年10月 [査読有り]

記述言語：英語掲載種別：研究論文（学術雑誌）共著

材料組織観察における不均一性の抽出と把握の重要性

日本金属学会金属組織観察の基礎と最近の進歩（金属学会セミナー） 35 - 42 1996年7月

記述言語：日本語掲載種別：研究論文（その他学術会議資料等）単著

Phenomenological aspects of fatigue life and fatigue crack initiation in high strength alloys at cryogenic temperature

O. Umezawa and K. Ishikawa

Materials Science and Engineering A 176 ( 1-2 ) 397 - 403 1994年 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）共著

Review of high cycle fatigue properties of structural materials at cryogenic temperatures

O. Umezawa, T. Ogata, T. Yuri, K. Nagai and K. Ishikawa

Advances in Cryogenic Engineering Materials 40 1231 - 1238 1994年 [査読有り]

Web of Science

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

High cycle fatigue properties of Ti-6Al-4V alloys at cryogenic temperatures

K. Nagai, T. Yuri, O. Umezawa, T. Ogata, K. Ishikawa, Y. Ito and T. Nishimura

Titanium `92 Sci. and Tech. Ⅱ 1827 - 1834 1993年12月

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Fatigue testing and properties of structural materials at cryogenic temperatures

K. Ishikawa, T. Yuri, O. Umezawa, K. Nagai and T. Ogata

Fusion Engineering and Design 20 429 - 435 1993年 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）共著

High-cycle fatigue properties of titanium alloys at cryogenic temperatures

O. Umezawa, K. Nagai, T. Yuri, T. Ogata and K. Ishikawa

Advances in Cryogenic Engineering Materials 38 175 - 182 1992年12月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Deformation structures in high-cycle fatigue of 0.1N-32Mn-7Cr steel at cryogenic temperatures

O. Umezawa and K. Ishikawa

Advances in Cryogenic Engineering Materials 38 141 - 148 1992年12月 [査読有り]

Web of Science

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Electrical and thermal conductivities and magnetization of some austenitic steels, titanium and titanium alloys at cryogenic temperatures

O. Umezawa and K. Ishikawa

Cryogenics 32 ( 10 ) 873 - 880 1992年10月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）共著

Fatigue properties of cold-rolled and sensitized SUS347 austenitic stainless steels at cryogenic temperatures

T. Yuri, K. Ishikawa, K. Nagai, T. Ogata and O. Umezawa

Cryogenics 32 ( ICMC Supplement ) 89 - 92 1992年 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Effect of strain rate on tensile behavior of some alloys at liquid helium temperature

K. Ishikawa, T. Ogata, T. Yuri, K. Nagai and O. Umezawa

Cryogenics 32 ( ICMC Supplement ) 67 - 70 1992年 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

High cycle fatigue of some austenitic steels at cryogenic temperatures"

K. Nagai, T. Yuri, O. Umezawa, T. Ogata and K. Ishikawa

Proc. Inter. Conf. on Stainless Steels 465 - 472 1991年10月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Discontinuous deformation of austenitic stainless steels in liquid helium

K. Ishikawa, T. Ogata, K. Nagai, T. Yuri and O. Umezawa

Proc. Inter. Conf. on Stainless Steels 449 - 456 1991年10月

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Strength and toughness of austenitic stainless steels at cryogenic temperatures"

T. Ogata, K. Ishikawa, K. Nagai, T. Yuri and O. Umezawa

Proc. Inter. Conf. on Stainless Steels 457 - 464 1991年10月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Effect of heat-treatment on physical properties of Ti-6Al-4V alloys at cryogenic temperatures

O. Umezawa, K. Nagai and K. Ishikawa

Sci. and Eng. of Light Metals 91 - 96 1991年9月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Cryogenic mechanical properties of Ti-6Al-4V alloys with three levels of oxygen content

K. Nagai, T. Yuri, T. Ogata, O. Umezawa, K. Ishikawa, T. Nishimura, T. Mizoguchi and Y. Ito

ISIJ International 31 ( 8 ) 882 - 889 1991年8月 [査読有り]

DOI

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：日本鉄鋼協会共著

その他リンク： https://www.jstage.jst.go.jp/article/isijinternational1989/31/8/31_8_882/_article

極低温構造材料の高サイクル疲労特性

長井　寿，由利哲美，梅澤　修，緒形俊夫，石川圭介

低温工学 26 ( 4 ) 255 - 262 1991年8月 [査読有り]

DOI

記述言語：日本語掲載種別：研究論文（学術雑誌）出版者・発行元：社団法人低温工学協会共著

その他リンク： https://www.jstage.jst.go.jp/article/jcsj1966/26/4/26_4_255/_article/-char/ja/

極低温高サイクル疲労における内部き裂発生

梅澤　修，長井　寿，由利哲美，緒形俊夫，石川圭介

低温工学 26 ( 4 ) 263 - 271 1991年8月 [査読有り]

DOI

記述言語：日本語掲載種別：研究論文（学術雑誌）出版者・発行元：社団法人低温工学協会共著

その他リンク： https://www.jstage.jst.go.jp/article/jcsj1966/26/4/26_4_263/_article/-char/ja/

Subsurface crack initiation in high cycle fatigue of 0.1N-32Mn-7cr steel at cryogenic temperatures

O. Umezawa, K. Nagai, T. Yuri and K. Ishikawa

Mechanical Behaviour of Materials VI 4 301 - 306 1991年7月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

極低温疲労試験における試験片の温度上昇と試験条件

緒形俊夫，石川圭介，長井　寿，由利哲美，梅澤　修

低温工学 26 ( 3 ) 190 - 196 1991年6月 [査読有り]

DOI

記述言語：日本語掲載種別：研究論文（学術雑誌）出版者・発行元：社団法人低温工学協会共著

その他リンク： https://www.jstage.jst.go.jp/article/jcsj1966/26/3/26_3_190/_article/-char/ja/

極低温疲労試験装置と運転結果

由利哲美，長井　寿，緒形俊夫，梅澤　修，石川圭介

低温工学 26 ( 3 ) 184 - 189 1991年6月

DOI

記述言語：日本語掲載種別：研究論文（学術雑誌）出版者・発行元：社団法人低温工学協会共著

その他リンク： https://www.jstage.jst.go.jp/article/jcsj1966/26/3/26_3_184/_article/-char/ja/

Internal crack initiation in high cycle fatigue at cryogenic temperatures

K. Nagai, O. Umezawa, T. Yuri and K. Ishikawa

Engineering Fracture Mechanics 40 ( 4-5 ) 957 - 965 1991年5月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）共著

Fatigue properties of titanium alloys in liquid helium

K. Ishikawa, K. Nagai, O. Umezawa, T. Yuri and T. Ogata

JSME International J., Series I 34 ( 3 ) 347 - 350 1991年3月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）共著

Low cycle fatigue and other mechanical properties of aged 316LN stainless steel at liquid helium temperature

T. Ogata, K. Ishikawa, K. Nagai, O. Umezawa and T. Yuri

Advances in Cryogenic Engineering Materials, eds. R.P. Reed and F.R. Ficket, Plenum Press, New York 36 1249 - 1255 1990年12月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Low temperature creep behavior of stainless steel

T. Ogata, O. Umezawa and K. Ishikawa

Advances in Cryogenic Engineering Materials, eds. R.P. Reed and F.R. Ficket, Plenum Press,New York 36 1233 - 1239 1990年12月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Fatigue 90, eds. H. Kitagawa and T. Tanaka Internal crack initiation in high cycle fatigue of Ti-6Al-4V alloys at cryogenic temperatures

O. Umezawa, K. Nagai and K. Ishikawa

Mater. and Component Eng. Pub., Birmingham 1 267 - 272 1990年7月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Ti-6Al-4V合金の極低温高サイクル疲労における内部き裂の発生

梅澤　修，長井　寿，石川圭介

鉄と鋼 76 ( 6 ) 924 - 931 1990年6月 [査読有り]

DOI

記述言語：日本語掲載種別：研究論文（学術雑誌）出版者・発行元：社団法人日本鉄鋼協会共著

その他リンク： https://www.jstage.jst.go.jp/article/tetsutohagane1955/76/6/76_6_924/_article/-char/ja/

Transmission electron microscopy study of high cycle fatigue deformation in Ti-5Al-2.5Sn extra low interstitial alloy at cryogenic temperatures

O. Umezawa, K. Nagai and K. Ishikawa

Materials Science and Engineering A 129 ( 2 ) 223 - 227 1990年 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）共著

Subsurface crack initiation in high cycle fatigue of Ti-5Al-2.5Sn extra-low interstitial alloy at liquid helium temperature

O. Umezawa, K. Nagai and K. Ishikawa

Materials Science and Engineering A 129 ( 2 ) 217 - 221 1990年 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）共著

Ti-5Al-2.5Sn ELI 合金の極低温高サイクル疲労におけるき裂の内部発生

梅澤　修，長井　寿，石川圭介

鉄と鋼 75 ( 1 ) 159 - 166 1989年1月 [査読有り]

DOI

記述言語：日本語掲載種別：研究論文（学術雑誌）出版者・発行元：社団法人日本鉄鋼協会共著

その他リンク： https://www.jstage.jst.go.jp/article/tetsutohagane1955/75/1/75_1_159/_article/-char/ja/

Fatigue and fracture of Ti alloys at cryogenic temperatures

K. Nagai, T. Yuri, O. Umezawa and K. Ishikawa

Proc. Magnet Technology (MT-11), eds. T. Sekiguchi and S. Shimamoto, Elsevier Applied Sci., London 1 754 - 759 1989年 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Creep and discontinuous deformation behavior of austenitic stainless steels at cryogenic temperatures

T. Ogata, K. Ishikawa, T. Yuri and O. Umezawa

Proc. Magnet Technology (MT-11), eds. T. Sekiguchi and S. Shimamoto, Elsevier Applied Sci., London 1 749 - 753 1989年 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Effects of specimen geometry on temperature and discontinuous deformation during tensile tests at liquid helium temperature

T. Ogata, K. Ishikawa, O. Umezawa and T. Yuri

Advances in Cryogenic Engineering Materials, eds. A.F. Clark and R.P. Reed, Plenum Press,New York 34 209 - 215 1988年12月 [査読有り]

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

Discontinuous deformation during load- and displacement- controlled tensile tests and optical observation in liquid helium

T. Ogata, K. Ishikawa, O. Umezawa and T. Yuri

Cryogenics 28 ( 8 ) 511 - 515 1988年8月 [査読有り]

DOI Web of Science

記述言語：英語掲載種別：研究論文（学術雑誌）共著

極低温におけるオーステナイト系ステンレス鋼の引張変形挙動と温度上昇に及ぼす試験片形状の影響

緒形俊夫，石川圭介，梅澤　修，由利哲美

低温工学 23 ( 4 ) 211 - 216 1988年4月 [査読有り]

記述言語：日本語掲載種別：研究論文（学術雑誌）出版者・発行元：公益社団法人低温工学・超電導学会共著

複合荷重下の2 1/4Cr-1Mo鋼のクリープ疲労相互作用

久保　清，八木晃一，金子隆一，梅澤　修

材料 37 ( 423 ) 67 - 73 1988年 [査読有り]

DOI

記述言語：日本語掲載種別：研究論文（学術雑誌）出版者・発行元：日本材料学会共著

A review on cryogenic temperature mechanical properties of Ti and its alloys

K. Nagai, T. Yuri, O. Umezawa and K. Ishikawa

Proc. Cryogenic Materials '88, eds. R.P. Reed, Z.S. Xing and E.W. Collings 2 727 - 736 1988年

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）共著

極低温荷重制御引張試験における温度上昇と変形挙動の直接観察

緒形俊夫，梅澤　修，由利哲美，石川圭介

低温工学 22 ( 2 ) 128 - 132 1987年4月 [査読有り]

DOI

記述言語：日本語掲載種別：研究論文（学術雑誌）出版者・発行元：公益社団法人低温工学・超電導学会共著

その他リンク： https://www.jstage.jst.go.jp/article/jcsj1966/22/2/22_2_128/_article/-char/ja/

このページの先頭へ▲

<梅澤 修>

論文 - 梅澤 修

<梅澤　修>

論文 - 梅澤　修