SHINOZUKA Jun

Affiliation

Faculty of Engineering, Division of Systems Research

Job Title

Associate Professor

Date of Birth

1967

Research Fields, Keywords

cutting, FEM, impact dynamics, thin film

Mail Address

E-mail address

Related SDGs




ORCID  https://orcid.org/0000-0001-5849-649X

The Best Research Achievement in Research Career 【 display / non-display

  • 【Published Thesis】 Measurement of the temperature distribution at the tool-chip interface by using a cutting tool with seven pairs of built-in micro Cu/Ni thermocouples  2016.01

    【Published Thesis】 Ultra High-Speed Cutting Experiment under the Cutting Condition that Cutting Speed Exceeds Plastic Wave Speed of Workpiece  2011

    【Published Thesis】 Investigation of ultra-high speed cutting mechanism by considering tool-chip friction property and inertia force derived from chip formation  2017.05

The Best Research Achievement in the last 5 years 【 display / non-display

Graduating School 【 display / non-display

  •  
    -
    1991

    Tokyo Institute of Technology   Faculty of Engineering   Department of Mechanical Physics   Graduated

Graduate School 【 display / non-display

  •  
    -
    1996

    Tokyo Institute of Technology  Graduate School, Division of Science and Engineering  Doctor Course  Accomplished credits for doctoral program

Campus Career 【 display / non-display

  • 2008.04
    -
    Now

    Duty   Yokohama National UniversityFaculty of Engineering   Division of Systems Research   Associate Professor  

  • 2018.04
    -
    Now

    Concurrently   Yokohama National UniversityGraduate school of Engineering Science   Department of Mechanical Engineering, Materials Science and Ocean Engineering   Associate Professor  

  • 2017.04
    -
    Now

    Concurrently   Yokohama National UniversityCollege of Engineering Science   Department of Mechanical Engineering, Materials Science and Ocean Engineering   Associate Professor  

  • 2011.04
    -
    Now

    Concurrently   Yokohama National UniversityCollege of Engineering Science   Department of Mechanical Engineering and Materials Science   Associate Professor  

  • 2008.04
    -
    Now

    Concurrently   Yokohama National UniversityGraduate School of Engineering   Department of Systems Integration   Associate Professor  

External Career 【 display / non-display

  • 2005.04
    -
    2008.03

    Ibaraki University, Japan   Lecturer  

  • 1996.05
    -
    2005.03

    Tokyo Institute of Technology, Japan   Research Assistant  

Field of expertise (Grants-in-aid for Scientific Research classification) 【 display / non-display

  • Production engineering/Processing studies

Qualification acquired 【 display / non-display

  • Electrical Work Person (second kind)

 

Research Career 【 display / non-display

  • -

    Project Year:  -   

  • Development of a high performance surface by an ultra high-speed cutting that plastic shock waves are induced

    Grant-in-Aid for Scientific Research  

    Project Year:  -   

  • Development of a cutting tool built-in minute sensors and clarification of the tribology and affinity at the tool-chip contact region

    Grant-in-Aid for Scientific Research  

    Project Year:  -   

Papers 【 display / non-display

  • Study on the monitoring of temperature distribution on the chip back surface around the chip root

    SHINOZUKA,Jun

    The 22nd International Symposium on Advances in Abrasive Technology     A30   2019.12  [Refereed]

    Single Work

  • Measurement of temperature distribution of the chip back surface during being formed by means of an infrared thermography camera

    Shinozuka Jun

    Proceedings of JSPE Semestrial Meeting ( The Japan Society for Precision Engineering )  2019 ( 0 )   36 - 37   2019

    Single Work

    DOI CiNii

  • Study on the improvement of the cutting performance of low-rigidity elastomers under room temperature

    SHINOZUKA Jun

        76 - 77   2018.11

    Single Work

  • Visualization of change in temperature distribution of all over the tool rake face from the beginning of cutting until the cutting state is in a quasi-state

    Jun Shinozuka

    ISAAT2018 Proceedings     Chapters 02, 36   2018.10  [Refereed]

    Single Work

  • Development of a cutting tool possessing multiple micro cutting edges on its face for the improvement of the machinability of elastomers

    Jun Shinozuka, Yuji Meguro and Shinji Maeda

    Proceedings of the 20th International Symposium on Advances in Abrasive Technology     399 - 402   2017.12  [Refereed]

    Joint Work

display all >>

Review Papers 【 display / non-display

  • FEM Simulation Technique on Metal Cutting Processes

    Electric Furnace Steel   78 ( 3 ) 233 - 240   2007

    Introduction and explanation (others)   Single Work

  • Clarification of Cutting Phenomena on Ultra High-Speed Cutting Processes and Generating od Advanced High Performance Surface by Ultra High-Speed Cutting

    Poster Exhibition -New Technologies of Machine Tool and Manufacturing- Abstract of Production Engineering Reserachers     88 - 89   2006

    Introduction and explanation (others)   Single Work

Academic Awards Received 【 display / non-display

  • The 15th International Machine Tool Engineer's Conference, Excellent Poster Award

    2012.11.03    

  • TICM2005 Best Paper Prize (TICM2005 Tehran International Congress on Manufacturing Engineering)

    2005    

Grant-in-Aid for Scientific Research 【 display / non-display

  • Grant-in-Aid for Scientific Research(C)

    Project Year: 2015.04  -  2017.03 

  • Grant-in-Aid for Scientific Research(B)

    Project Year: 2010.04  -  2012.03